Land Pride SB10 Series Operator's Manual page 20

Section 3: Tractor Hook-up & Unhook
Section 3: Tractor Hook-up & Unhook
Driveline Assembly
Refer to Figure 3-2 on page 17:
IMPORTANT: An additional driveline may be
required if implement is attached to more than one
tractor or if a Quick Hitch is used.
IMPORTANT: The driveline must be lubricated
before putting it into service. Refer to "Lubrication
Points" on page 36.
Refer to Figure 3-2 on page 17:
1. Remove rubber protective sleeve (#6) from gearbox
input shaft and discard.
2. Slide shearbolt end of driveline (#7) onto gearbox
input shaft until hole in driveline yoke aligns with
groove in gearbox shaft.
3. Insert 1/2"-13 x 3 1/2" GR2 bolt (#2) and secure with
hex nut (#3) and jam nut (#4). Draw hex nut (#3) up
snug (do not tighten). Tighten jam
nut (#4) against hex nut (#3).
4. Push/pull on driveline yoke to be sure it is securely
fastened to the gearbox shaft.
Tractor Hook-up
Refer to Figure 3-2 on page 17:
!
DANGER
To avoid serious injury or death:
A crushing hazard exists while hooking-up and unhooking
implement. Keep people and animals away while backing-up
to implement or pulling away from implement. Do not operate
hydraulic controls while a person or animal is directly behind
the power machine or near the implement.
!
WARNING
To avoid serious injury or death:
Always shut tractor down using "Tractor Shutdown
Procedure" provided in this manual before dismounting
tractor.
IMPORTANT: The tractor's lower 3-point arms must
be stabilized to prevent side-to-side movement.
Most tractors have sway blocks or adjustable chains
for this purpose.
NOTE: Land Pride's Quick Hitch can be attached to
the tractor to provide quick and easy 3-point hook-
up and detachment. An additional driveline may be
required if a Quick Hitch is used. See your nearest
Land Pride dealer to purchase a Quick Hitch.
NOTE: Review "Hitch Pin Locations" on page 22
before hooking tractor to Snow Blower.
16
SB1051, SB1064, SB1574, & SB2584 with S/N 881641+ Snow Blowers 370-430M
Table of Contents
The SB10 & SB15 Series require a 3-point Cat. l hitch.
The SB25 Series will receive Cat. l & ll 3-point hitches.
The lower 3-point arms must be stabilized to prevent
side-to-side movement. Most tractors have sway blocks
or adjustable chains for this purpose.
1. Extend or retract 3-point hitch to position the Snow
Blower farther from or closer to the tractor. Refer to
"Extend/Retract 3-Point Hitch Frame" on page 15
for detailed instructions.
2. Quick Hitch bushing is mounted in the lower holes on
the center clevis as shown when making a standard
3-point hooking-up or standard Quick Hitch hook-up.
Review "Hitch Pin Locations" on page 22 before
hooking-up to tractor.
3. Slowly back tractor to the Snow Blower while using
tractor's 3-point hydraulic control lever to align lower
3-point arm hitch holes with lower hitch pins (#1).
4. Place gear selector in park or in neutral with park
brake set, shut engine off, and remove switch key
before dismounting tractor.
5. Attach lower 3-point arms to clevises (#9) with hitch
pins (#1). Secure hitch pins with linchpins (#5).
6. Connect top center link hitch hole to upper clevis
hitch holes with hitch pin and hitch pin keeper.
(Hitch pin and keeper are supplied by customer.
If needed, cut this end of crank handle
off to shorten length of handle.
Adjust Chute Rotation Handle
Refer to Figure 3-1:
!
CAUTION
To avoid minor or moderate injury:
If adjusted too long, the rotational handle can come in contact
with the tractor or create a pinch point between the tractor
and Snow Blower.
1. Remove wire retaining pin (#2) and move rotation
handle (#1) in or out as needed to keep rotation
handle from making contact with tractor or creating a
pinch point between tractor and Snow Blower.
2. Be sure to check hand crank length when hooking up
to the Snow Blower. Take measurement with Snow
Blower raised fully up. If needed, cut 3" or more off
straight end of rotational hand crank (#1).
3. Replace wire retaining pin (#2). Make sure wire
retainer is caught over end of pin.
Manual Chute Rotation Handle
Figure 3-1
37094
1/23/19