Assembly Instructions - Landoll 2220 Series Operator's Manual

ASSEMBLY INSTRUCTIONS

It is very im por tant that your new 2220 Se ries
Disc Chisel be prop erly as sem bled, ad justed and
lu bri cated be fore use. Il lus tra tions to as sist with the
as sem bly pro cess are pro vided in Sec tion 2,
"Stan dard Speci fi ca tions". They show proper
shank, disc gang and mount ing bracket spac ings. Il -
lus tra tions in this sec tion show proper as sem bly
pro ce dures. Re move paint from grease fit tings. Re -
place any grease fit tings that are dam aged or miss -
ing. Be sure to re turn bolts, clips, etc., to their origi -
nal lo ca tions.
To in sure align ment of as sem blies, leave the
nuts loose un til com ple tion of fi nal as sem bly. Use
lock wash ers or flat wash ers as speci fied. Spread all
cot ter pins.
Af ter com ple tion of fi nal as sem bly, tighten all
nuts evenly to pre vent mis align ment, dis tor tion or
bind ing. Tighten all bolts and nuts to the rec om -
mended torques shown in Ta ble 2-1, "Stan dard
Bolt Torques".
DAN GER
DISC BLADES
SHARP. EX ER CISE EX TREME CARE
WHEN WORK ING ON OR NEAR DISC
BLADES. DO NOT AL LOW DISCS TO
ROLL OVER OR FALL ONTO ANY
BOD ILY PART.
WRENCHES TO SLIP WHEN WORK -
ING NEAR DISC BLADES. NEVER
PUSH WRENCHES TO WARD DISC
BLADES. DO NOT CLIMB OVER MA -
CHINE ABOVE DISC BLADES. FAIL -
URE TO STAY CLEAR OF DISC
BLADE EDGES CAN CAUSE SE RI -
OUS PER SONAL IN JURY OR DEATH.
CAU TION
IN COR RECT AD JUST MENT OF DISC
AD JUST RODS WILL CAUSE PER MA -
NENT EQUIP MENT DAM AGE.
ARE EX TREMELY
DO NOT AL LOW
WARN ING
DO NOT AT TEMPT TO LIFT HEAVY
PARTS (SUCH AS THE FRAME, DISC
GANGS, ROCK SHAFT, AND PULL
HITCH) MANU ALLY. USE A HOIST OR
A FORK LIFT TO MOVE THESE
PARTS INTO PO SI TION.
DAN GER
TO PRE VENT AC CI DEN TAL LOW ER -
ING:
1. ALL HY DRAU LI CALLY ELE VATED
EQUIP MENT MUST BE LOCKED OUT
US ING THE CYL IN DER LOCK OUTS:
2. LOWER EQUIP MENT
GROUND WHILE
WHEN IT IS IDLE.
FAIL URE TO TAKE MEAS URES TO
PRE VENT AC CI DEN TAL LOW ER ING
MAY RE SULT
SONAL IN JURY OR DEATH.
CAU TION
BE SURE DEPTH STOPS ARE EQUAL
LENGTHS ON ALL CYL IN DERS. US -
ING UNE QUAL
LENGTHS CAN CAUSE PER MA NENT
EQUIP MENT DAM AGE.
CAU TION
BE SURE TO BLEED THE HY DRAU -
LIC SYS TEM OF ALL AIR IN LINES
AF TER IN STAL LA TION. FAIL URE TO
BLEED THE SYS TEM OF ALL AIR
CAN RE SULT IN IM PROPER MA -
CHINE OP ERA TION.
TO THE
SERV IC ING
IN SE RI OUS PER -
DEPTH STOP
3
OR
3-1