Related Manuals for pellenc SELION C21 HD
Summary of Contents for pellenc SELION C21 HD
- Page 1 Translation of the origi- nal operating instructions CHAINSAW SELION C21 HD 51_149277-A OPERATING INSTRUCTIONS 01/2020 READ THE OPERATING INSTRUCTIONS MANUAL CAREFULLY BEFORE USE...
-
Page 3: Table Of Contents
CHAINSAW SELION C21 HD 51_149277-A TABLE OF CONTENTS 1. INTRODUCTION ........................5 2. SAFETY ........................... 6 2.1. INTENDED USAGE .......................... 2.2. GENERAL SAFETY WARNINGS FOR THE TOOL ................ 2.2.1. WORK AREA SAFETY ........................2.2.2. ELECTRICAL SAFETY ........................2.2.3. PERSONAL SAFETY ......................... - Page 4 CHAINSAW SELION C21 HD 51_149277-A 5. USING THE TOOL ........................ 20 5.1. HOLDING THE TOOL ........................5.2. START-UP ............................5.3. ELECTRONIC ..........................6. MAINTENANCE ........................22 6.1. THE FOUR BASIC RULES ......................6.2. MAINTENANCE FREQUENCY ...................... 6.3. REPLACING THE CHAIN AND THE CHAIN GUIDE ..............
-
Page 5: Introduction
51_149277-A 1. INTRODUCTION Dear Customer, Thank you for purchasing your Chainsaw Selion C21 HD. Correctly used and maintained, this tool will give a satis- factory performance for many years. Warning Your device contains numerous recoverable or recyclable materials. Return it to your dealer or, failing this, to an approved servicing centre to be treated. -
Page 6: Safety
2. SAFETY 2.1. INTENDED USAGE • The Chainsaw Selion C21 HD is intended for cutting only wood and branches up to a diameter corresponding to the length of the chainsaw guide bar. • The Chainsaw Selion C21 HD should not be used for ground use. -
Page 7: Personal Safety
CHAINSAW SELION C21 HD 51_149277-A Use an extension cord suitable for outdoor use when operating power tools outdoors. Use a cord suitable for outdoors to reduce the risk of electric shock. Use a power supply protected by a residual current device (RCD) when the power tool is operated in a damp location. -
Page 8: Upkeep
2.2.7. TOOL’S END OF LIFE MANAGEMENT When the tool reaches the end of its life, PELLENC keeps the end of life sheet of the equipment at disposal. The end of life sheet provides instructions for safely removing components. -
Page 9: Causes And Operator Prevention Of Kickback
CHAINSAW SELION C21 HD 51_149277-A 2.4. CAUSES AND OPERATOR PREVENTION OF KICKBACK Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. -
Page 10: Good Practices For Safe Working
• Keep your left arm straight for better control. • Hold the chainsaw at your side, and not in front of you. • Use genuine PELLENC chains and guides. • Keep the chain, the guide and the sprocket in good working condition. -
Page 11: Working With Tree Service Hand-Held Chainsaws Using A Rope And Harness
CHAINSAW SELION C21 HD 51_149277-A Do not expose to rain. This chainsaw is for trained tree service operators only. 2.8. WORKING WITH TREE SERVICE HAND-HELD CHAINSAWS USING A ROPE AND HARNESS 2.8.1. OVERVIEW This annex sets out working practices aimed at reducing the risk of injury from tree service chainsaws when working at height from a rope and harness. -
Page 12: Preparing To Use The Chainsaw Up In A Tree
CHAINSAW SELION C21 HD 51_149277-A 2.8.3. PREPARING TO USE THE CHAINSAW UP IN A TREE The chainsaw should be fitted with a suitable strop for attachment to the operator’s harness. Secure the strop around the attachment point on the rear of the chainsaw;... -
Page 13: Securing The Work Position For Two-Handed Use
CHAINSAW SELION C21 HD 51_149277-A 2.8.5. SECURING THE WORK POSITION FOR TWO-HANDED USE In order to allow the saw to be held with both hands, as a general rule operators should aim for a secure work position in which they operate the saw at •... -
Page 14: Freeing A Trapped Saw
• Risk of cuts due to unexpected and sudden movement of the guide bar • Risk of cutting or piercing injuries related to the projection of parts of the Chainsaw Selion C21 HD • Risk of projections of splinters, bark, etc. while sawing •... -
Page 15: Description And Technical Characteristics
The automatic chain tensioning (PELLENC innovation) facilitates tool maintenance! The automatic chain tensioning system (PELLENC innovation) facilitates the installation of the chain and its tension adjustment. Position the guide, and clip it, the guide is in position! You can permanently lock it in position using the retractable wrench (14) (PELLENC innovation). -
Page 16: Technical Features
CHAINSAW SELION C21 HD 51_149277-A 3.2. TECHNICAL FEATURES 3.2.1. GENERAL CHARACTERISTICS Selion C21 HD Battery life Depends on use and battery type NOMINAL VOLTAGE 43.2 V Chain oil tank capacity 25 cl Useful cutting length / chain guide See the chart Section 3.2.2, “Chains and chain guides compatibility”... -
Page 17: Vibration Levels
CHAINSAW SELION C21 HD 51_149277-A 3.2.5. VIBRATION LEVELS Determination of the vibration levels is based on the operating conditions at the nominal maximum speed. Vibration level according to 60745-1 of EN 60745-2-13 Vibration emission value (measurement uncertainty K = 1.5 m / s²) -
Page 18: Commissioning
CHAINSAW SELION C21 HD 51_149277-A 4. COMMISSIONING Warning To ensure the proper functioning of the tool, all commissioning procedures must be carried out before using it for the first time. 4.1. ASSEMBLY OF THE CHAIN AND CHAIN GUIDE (1ST USE) -
Page 19: Chain Lubrication (First Use)
CHAINSAW SELION C21 HD 51_149277-A 4.2. CHAIN LUBRICATION (FIRST USE) 4.2.1. FILLING THE CHAIN OIL RESERVOIR Before the first use, it is essential to fill the chain oil reser- voir with the specific chain and guide oil (Ref.: 85920). Unscrew the oil reservoir cap (12) Carefully pour the guide and chain oil into the reser- voir. -
Page 20: Using The Tool
«0». 5.2. START-UP Remove the chain guide protector. Set the Pellenc tool battery On/Off switch to the On position “I”. From the moment the indicator light (15) comes on and the battery emits 3 beeps, the tool is energized and ready to operate. -
Page 21: Electronic
CHAINSAW SELION C21 HD 51_149277-A Important Allow the chainsaw to cut without pressing excessively. Always start the motor before bringing the chainsaw into contact with the wood. 5.3. ELECTRONIC Your chainsaw is fitted with an impact detection system In the event of impact (kickback) your chainsaw will stop immediately. -
Page 22: Maintenance
CHAINSAW SELION C21 HD 51_149277-A 6. MAINTENANCE 6.1. THE FOUR BASIC RULES Caution Before working on the tool, check that the On / Off switch is in the off position «0» and disconnect the battery power lead. Your chainsaw is fitted with an impact detection system In the event of impact (kickback) your chainsaw will stop immediately. -
Page 23: Maintenance Frequency
CHAINSAW SELION C21 HD 51_149277-A Rule No. 4: The depth limiters must be correctly adjusted. • The depth limiters must be correctly adjusted and of the right shape to ensure good performance and safe- • Refer to Section 6.10, “Adjusting the depth limiters”. -
Page 24: Automatic Chain Tension
CHAINSAW SELION C21 HD 51_149277-A Warning Never use a chain or a guide other than those specified by PELLENC, otherwise there is a risk of personal injury. 6.4. AUTOMATIC CHAIN TENSION Important Check and adjust the tension of the chain: •... - Page 25 CHAINSAW SELION C21 HD 51_149277-A Caution Before working on the tool, check that the On / Off switch is in the off position «0» and disconnect the battery power lead. Set the battery switch to "0" and disconnect the con- nector.
-
Page 26: Chain Lubrication
CHAINSAW SELION C21 HD 51_149277-A 6.5. CHAIN LUBRICATION Lubrication is carried out continuously thanks to the PELLENC innovation of electronic oil flow management. Check that there is always oil in the reservoir to ensure continuous lubrication. Filling the oil reservoir Use special guide and chain oil (P/No. -
Page 27: Forced Chain Lubrication
CHAINSAW SELION C21 HD 51_149277-A 6.6. FORCED CHAIN LUBRICATION The forced lubrication cycle distributes the oil from the reservoir to the mechanism. When to carry out the forced lubrication cycle? The lubrication cycle is always carried out with the lubri- cant reservoir filled and: •... -
Page 28: Chain Guide Lubrication
CHAINSAW SELION C21 HD 51_149277-A Turn the chain guide round every week. 6.8. CHAIN GUIDE LUBRICATION Lubricate the chain guide every day using a grease gun (ref. 68518). Note Consumables are sold separately. 6.9. SHARPENING THE CHAIN Caution Before working on the tool, check that the On / Off switch is in the off position «0»... -
Page 29: Adjusting The Depth Limiters
CHAINSAW SELION C21 HD 51_149277-A Sharpen the cutters from one side of the chain by filing from the interior toward the exterior. Only file by pushing. Hold the mark on the file holder parallel with the mark on the platen. Proceed in the opposite manner for the other side. - Page 30 CHAINSAW SELION C21 HD 51_149277-A «0» and disconnect the battery power lead. Check the depth limiters every 2 or 3 sharpening op- erations. Use a depth gage corresponding to the type of chain to be sharpened. Place the depth gauge on the gouge.
-
Page 31: Checking And Replacing The Sprocket
CHAINSAW SELION C21 HD 51_149277-A Caution Do not file or damage the top of the drive links or the side links fitted with an anti-kickback guard. After reducing the height of the depth limiters, round off the angle to maintain the original shape of the depth limiters. -
Page 32: Cleaning The Chain Guide
CHAINSAW SELION C21 HD 51_149277-A 6.12. CLEANING THE CHAIN GUIDE Set the battery switch to "0" and disconnect the con- nector. Remove the chain guide (7) and the chain (6) (refer to Section 6.3, “Replacing the chain and the chain guide”). -
Page 33: Incidents And Troubleshooting
The Chainsaw Selion C21 HD will not Check the following points: start • Check that the Chainsaw Selion C21 HD is correctly connected to the battery. • Check the battery charge level. If none of these procedures succeeds in resolving the problem, contact a... -
Page 34: Storage And Transport
CHAINSAW SELION C21 HD 51_149277-A 8. STORAGE AND TRANSPORT 8.1. CHAIN PROTECTION • Put on the chain protector (18) during transport and storage. • Always clean the tool before storing it. • Make sure the chain is sharp before storing the tool. -
Page 35: Accessories And Consumables
CHAINSAW SELION C21 HD 51_149277-A 9. ACCESSORIES AND CONSUMABLES 9.1. ACCESSORIES References: Grease pump for chain guide 68518 Retaining clamp 68519 Sharpening kit 68520 Round file (box of 12) 68521 Flat file (box of 12) 68522 Round file (pack of 3) 68611 9.2. -
Page 36: Warranties
The warranty is fully integral to the product sold by PELLENC. 10.1.2.1.2. SPARE PARTS The commercial warranty also covers original PELLENCspare parts, excluding labour and to the exclusion of certain... -
Page 37: Paid After-Sales Service
PELLENC Products are guaranteed under the commercial warranty as from delivery to the customer for a period of two (2) years for products connected to a PELLENC battery, and for a period of one (1) year for other PELLENC products. - Page 38 Paid after-sales service also covers original PELLENC spare parts, excluding labour and outside the legal and commercial warranty period. In case of replacement of original PELLENC spare parts in the context of after-sales service, said latter are covered by a warranty of one year as from the installation date.
-
Page 39: Ec Statement Of Compliance
CHAINSAW SELION C21 HD 51_149277-A 11. EC STATEMENT OF COMPLIANCE 11.1. "EC" DECLARATION OF CONFORMITY: SELION C MANUFACTURER PELLENC ADDRESS Quartier Notre-Dame - 84120 Pertuis (France) ENTITY AUTHORIZED TO COMPILE THE TECHNICAL FILE PELLENC ADDRESS Quartier Notre-Dame - 84120 Pertuis... - Page 44 PELLENC Quartier Notre Dame - 84120 Pertuis (France)