Table of Contents
Advertisement
Quick Links
7370 Series Multi-Point Lock
for Window Shutter Applications
Installation Instructions
Recommended Installation:
Install 7370 so that the
deadbolt is equidistant from
the top and bottom of the
shutter.
Attention Installer
Any retrofit or other field modification to a fire rated opening can
potentially impact the fire rating of the opening, and Yale Locks &
Hardware makes no representations or warranties concerning
what such impact may be in any specific situation. When
retrofitting any portion of an existing fire rated opening, or
specifying and installing a new fire-rated opening, please consult
with a code specialist or local code official (Authority Having
Jurisdiction) to ensure compliance with all applicable codes and
ratings.
80-8470-7370-010 (10-12)
An ASSA ABLOY Group brand
Advertisement
Table of Contents
Related Manuals for Assa Abloy Yale 7370 Series
Summary of Contents for Assa Abloy Yale 7370 Series
- Page 1 (Authority Having Jurisdiction) to ensure compliance with all applicable codes and ratings. 80-8470-7370-010 (10-12) An ASSA ABLOY Group brand...
-
Page 2: Table Of Contents
UL-approved for both FEMA 361 and ICC 500 guidelines for inswing window shutters. This instruction sheet will take you through the following steps for full installation. Installation Jig Components Drill Guide for Deadbolt Case 80-8470-7370-010 (10-12) An ASSA ABLOY Group brand... -
Page 3: Step 1 - Installation Of Deadbolt Assembly
Note the orientation of the bottom bolt assembly the double screw head side (not shown in this image) should be facing the hinge side of the shutter. Continue on next page…………. 80-8470-7370-010 (10-12) An ASSA ABLOY Group brand... -
Page 4: Step 3 - Installation Of Top Pusher Assembly
It should be on the same side as the plunger pin. • Fasten the Top Strike plate and Top Pusher Assembly to the top of the shutter using (2) #12-24 x 1" Flat Head Cap Screws. 80-8470-7370-010 (10-12) An ASSA ABLOY Group brand... -
Page 5: Step 4 - Aligning Assemblies In Preparation For Drilling And Pinning 5
The lifting platform jig will now be in position to allow sliding the lifting platform (shown in step 2) so that it rests against the shelf of the jig. Continued on next page…………. 80-8470-7370-010 (10-12) An ASSA ABLOY Group brand... - Page 6 • Next secure the platforms position by tightening the cone point set screw (item 2). This will assure the point on the set screw embeds itself firmly into the bottom rod. 80-8470-7370-010 (10-12) An ASSA ABLOY Group brand...
-
Page 7: Step 5 - Applying The Drill Jig For Proper Drilling
• Using the Drill Guide Hole, drill a 1/8" hole (drill provided with jig components) thru both sets of rods. 80-8470-7370-010 (10-12) An ASSA ABLOY Group brand... -
Page 8: Step 6 - Pinning The Rods To Engage The Deadbolt Lever
• Visually align the mounting holes of the inside escutcheon to the mounting posts from the outside escutcheon. • Insert 4 mounting screws #12 -24 x 1-1/2" and tighten screws. 80-8470-7370-010 (10-12) An ASSA ABLOY Group brand... -
Page 9: Step 8 - Installation Of Cylinder In Outside Trim (Optional)
Step 9 – Assemble the Top Latch to the Frame • Assembly the top latch into the top of the frame using (4) 1/4"-20 x 1" Flat Head Cap Screws. The angled surface should face the shutter. 80-8470-7370-010 (10-12) An ASSA ABLOY Group brand... -
Page 10: Step 10 - Installation Of Deadbolt Strike
Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company. Yale® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Other products' brand names may be trademarks or registered trademarks of their respective owners and are mentioned for reference purposes only.