Assa Abloy Yale 5300 Series Installation Instructions

Assa Abloy Yale 5300 Series Installation Instructions

Grade 2 cylindrical knob lockset

Advertisement

Quick Links

1

Mark Door

Mark horizontal line across the edge
of the door at the height you want to
install knob. Fold template over
edge of door, centering on horizontal
line. Mark centers of holes.
4
-IMPORTANT-

Adjust for Door Thickness

To adjust lock rotate outside rose and
position as indicated in accord with the
door thickness. To adjust for any door
thickness between 1-3/8" and 1-3/4"
set the rose plate at a suitable
intermediate position.
1-3/8" (35mm)
1/8" (3.2mm)
5/16" (8.0mm)
1-3/4" (44mm)
Lock Case
Outside Rose
7

Install Inside Knob

Align lug on knob with narrow slot on
side of spindle and push knob all the
way in until retainer clicks into slot on
knob.
NOTE: For 5305 lock only.
Refer to Step 9 before installing
inside knob. When installing knob
make sure button is pushed in and
turned clockwise to lock outside knob.
An ASSA ABLOY Group brand
5300 Series Grade 2
Cylindrical Knob Lockset
Installation Instructions
2

Install Latch Unit

Bore 2-1/8" hole through door, and hole
into edge of door at points marked on
the door. Cut out for latch front 5/32"
deep and install latch unit.
Notches required
on Hard Laminate
& Metal Doors
5

Install Lock

With lock case in place, insert lock
assembly into 2-1/8" (54mm) hole,
making sure that lock case hooks the
retainer legs and retractor engages the
bolt tail. Do Not Force.
Caution: If deadlocking latch unit is
installed, do not attempt to mount
lock unit with door closed, as
deadlocking plunger bar will interfere.
Retractor
Retainer Leg
Bolt Tail
Lock Case
8

Install Strike

Mark height line for strike on jamb.
Mark vertical centerline on jamb. This
centerline must be same distance from
door stop as latch unit centerline is from
edge of door which will hit stop. Cut
mortise in jamb for strike and box (if
used). Insert box and strike and tighten
screws securely.
(497)
3

Remove Inside Knob

4
If knob retainer is not visible, turn inside
knob counterclockwise approximately
45°. Use small nail or wire to depress
retainer and slide knob off.
NOTE: For 5316 Lockset only. To
remove inside knob, follow instructions
in Step 9 under heading "All 5300
Series Locksets".
6

Install Inside Rose Plate and Rose

Slip on rose plate and locate screw
holes on vertical centerline. Insert
machine screws and tighten
alternately to obtain secure attachment.
Place rose over rose plate aligning
notch in rose with tab on rose plate and
snap rose down flush with door.
Rose
9
-IMPORTANT-
All locks are set for a right hand door.
If the lock is properly installed, the cuts
on the key will be facing up when the
key is inserted into the knob.
(371)
Right Way
Vertical
Rose Plate
Tab
Notch
Wrong Way
80-9150-0033-010 (08-12)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Yale 5300 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Assa Abloy Yale 5300 Series

  • Page 1 When installing knob used). Insert box and strike and tighten make sure button is pushed in and screws securely. turned clockwise to lock outside knob. (497) (371) Right Way Wrong Way 80-9150-0033-010 (08-12) An ASSA ABLOY Group brand...
  • Page 2 Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company. Yale® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Other products' brand names may be trademarks or registered trademarks of their respective owners and are mentioned for reference purposes only.

This manual is also suitable for:

Yale 5320Yale 5316Yale 5305

Table of Contents