Appendix; Configuration And Parameterization Using A Gsd File With Profibus Dp And Profinet Io; 2Ai Rtd Ex I Configuration; Profibus Dp Fieldbus Couplers/Controllers - WAGO 750-481/003-000 Manual

56

Appendix

Pos : 38 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 1/Anhang - Übersc hrift 1 @ 4\mod_1239874070437_21.doc x @ 30560 @ 1 @ 1
8 Appendix
Pos : 39 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 2/Konfigurieren und Parametrier en per GSD-D atei bei PROF IBU S D P und PROF INET IO- Übersc hrift 2 @ 19\mod_1399559517054_21.doc x @ 153249 @ 2 @ 1
8.1 Configuration and Parameterization using a GSD
File with PROFIBUS DP and PROFINET IO
Pos : 40 /Serie 750 ( WAGO-I/O-SYST EM)/In Betrieb nehmen/Parametrier en über GSD-Datei/Hi nweis : Vor aus setzung GSD Par ametrierung Versi on Koppl er/Contr oller 750-04xx @ 28\mod_1486470618507_21.doc x @ 405368 @ @ 1
Note
Requirement
A fieldbus coupler/controller must be used to parameterize the I/O
module750-481/003-000 (2AI RTD Ex i) via GSD file:
Pos : 41 /Serie 750 ( WAGO-I/O-SYST EM)/In Betrieb nehmen/Parametrier en über GSD-Datei/Hi nweis : GSD-D atei mit WAGO- I/O-CH ECK übers chr eiben @ 28\mod_1486642416009_21.doc x @ 407147 @ @ 1
Behavior after Overwriting with WAGO-I/O-CHECK !
If WAGO-I/O-CHECK is used to overwrite a parameterization made with the GSD
file, the I/O module operates with the WAGO-I/O-CHECK settings until the 750-
333 and 750-833 Fieldbus Couplers/Controllers are restarted.
After restart, the I/O module is re-parameterized via PROFIBUS using the GSD
settings.
Pos : 42 /Serie 750 ( WAGO-I/O-SYST EM)/In Betrieb nehmen/Parametrier en über GSD-Datei/Anhang: GSD-Datei en - Konfiguration + Par ametrierung 2 AI 750-0481/003- 000 @ 28\mod_1486025397746_21.doc x @ 405038 @ 3443444 @ 1
Pos : 89 /All e Seri en (Allgemei ne Module)/Ü berschriften für alle Serien/Konfigurier en und Par ametri eren per GSD bei PROF IBU S D P und PROF INET IO - Ü bersc hrift 2 @ 15\mod_1367213583437_6.doc x @ 118148 @ 2 @ 1
Pos : 90 /Serie 750 ( WAGO-I/O-SYST EM)/Anhang/Konfiguri eren und Par ametrieren per GSD bei PR OFIBUS D P und PR OFIN ET IO 750-0652 @ 15\mod_1366809580641_6.doc x @ 117978 @ 3443444 @ 1
8.1.1

2AI RTD Ex i Configuration

8.1.1.1

PROFIBUS DP Fieldbus Couplers/Controllers

750-333(/0xx-000), 750-833(/0xx-000)

When using the aforementioned PROFIBUS DP fieldbus devices, the process
image size is configured by selecting the corresponding GSD entry.

Table 31: PROFIBUS DP Configuration

GSD Entry
Module
750-481 2AI/RTD/Ex i
750-481 2AI/RTD/Ex i, PRM
750-481 2AI/RTD/Ex i RA, PRM
750-481 2AI/RTD/Ex i RA
PFC 750-481 2AI/RTD/Ex i
*)
Only available with 750-833(/0xx-000)
• PROFIBUS DP 750-333(/0xx-000): > Firmware Version 19
• PROFIBUS DP 750-833(/0xx-000): > Firmware Version 18
• PROFINET IO 750-375(/025-000): > Firmware Version 01
• PROFINET IO 750-377(/025-000): > Firmware Version 01
*)
PI Length/[Byte]
Sub- I
Module
4 n/a
n/a
6
n/a n/a
V 1.4.0 HW-Version 07, SW-Version 41
WAGO-I/O-SYSTEM 750
750-481/003-000 2AI RTD Ex i
Data Type
O
INT16
6 {UINT8, INT16}
n/a
Inst.
2
n/a
Manual