Nice AVIO600 Instructions And Warnings For Installation And Use page 50

TECHNICAL CHARACTERISTICS OF THE VARIOUS COMPONENTS OF THE PRODUCT
The product AVIO600 / AVIO1000 is produced by Nice S.p.a. (TV) I. In order to improve its products, Nice S.p.a. reserves the right to modify their tech-
nical characteristics at any time ithout prior notice. In any case, the manufacturer guarantees their functionality and fitness for the intended purposes.
Note: all the technical characteristics refer to a temperature of 20°C.
DESCRIPTION
Type
Adopted technology
Peak thrust [corresponds to the force
necessary to move a leaf]
Nominal torque [corresponds to the
force necessary to keep a leaf moving]
Idling speed
Speed at nominal torque
Maximum frequency of cycles
Maximum continuous cycle time
Operating Limits
Power supply AVIO
Max. absorbed power
Insulation class
Emergency power supply
Flashing light output
Courtesy light
BUS output
"SbS" input
"STOP" input
Radio aerial input
Maximum cable length
Remote control possibility
ECCO5... transmitters memorised
Range of ECCO5... transmitters
Programmable functions
Self-programmed functions
Operating ambient temperature
Assembly
Protection rating
Dimensions / weight
Model GD102
Electromechanical gearmotor for automated sectional and overhead doors incorporating a control
unit complete with radio receiver for "ECCO5..." transmitters.
24V motor, helical teeth reduction gear; drive guide with timing belt and mechanical release.
A transformer inside the motor but separated from the control unit reduces mains voltage to the
nominal voltage of 24V
10,8 Nm
[600 N]
5,4 Nm
[300 N]
0,10 m/s in "slow" speed mode
0,18 m/s in "fast" speed mode
0,05 m/s in "slow" speed mode
0,09 m/s in "fast" speed mode
(For a maximum of approx. 10 cycles per hour. A maximum of 5 cycles per hour
4 minutes (the control unit limits the continuous operation)
Its structural characteristics make it suitable for use on sectional and overhead doors with coun-
terweights that are within the dimensions and limits indicated in table 7
250 W
I (a safety grounding system is required)
---
For Led visual signalling devices (mod. FL200)
12V lamp maximum 10W BA15 socket (automotive type lamp), stays on 60s after the manoeuvre
One output with a maximum
load of 1 ECSBus unit
For normally open contacts (the closing of the contact causes the "Step-by-Step" command)
For normally open contacts and/or for 8,2kΩ constant resistance, or normally closed contacts
with recognition of the "normal" status (any variation from the memorised status causes the
52 Ω for RG58 or similar type of cable
Mains power supply: 30 m; inputs/outputs: 20m with aerial cable preferably shorter than 5m
(observe the directions regarding the minimum gauge and type of cable)
With ECCO5... transmitters, the control unit can receive one or more of the following commands:
"Step-by-Step", "Partial opening", "Open only" and "Close only"
Up to 150 if memorised in mode 1
From 10 to 50 m ithout aerial, from 50 to 100 m ith aerial incorporated in the FL200 ashing
light. The range can vary if there are obstacles or electromagnetic disturbances, and is affected by
the position of the receiving aerial incorporated in the ashing light.
"Cycle" or "Complete cycle" operation (automatic closing)
The pause time in the "complete cycle" mode can be set at 10, 20, 40, 80 seconds
The sensitivity of the obstacle detection system can be selected from 4 levels
The operation of the "Step-by-Step" command can be selected from 4 modes
Automatic detection of devices connected to the BUS Output.
Automatic detection of the type of STOP device (NO or NC contact or 8,2kΩ resistance)
Automatic detection of door length and calculation of deceleration points.
DATA
Model GD103
used by the automation system.
0,10 m/s in "slow" speed mode
0,15 m/s in "fast" speed mode
0,05 m/s in "slow" speed mode
0,08 m/s in "fast" speed mode
50 complete cycles per day
is permitted at 50°C
230 V (±10%) 50/60 Hz
with PR100 accessory
One output with a maximum
load of 6 ECSbus units
"STOP" command)
"Slow" or "fast" motor speed
-20°C...+50°C
Horizontal
IP40
380 x 280 x h 110 mm / 4 kg
18 Nm
[1,000 N]
9 Nm
[500 N]
370 W
English – 23