DeLaval VMS 2008 Instruction Book page 194

M M m m Alarm text Alarm text
6 6 1 1 AlcomIO AlcomIO Deviation Deviation
board reset board reset
node ... bus node ... bus
... ...
6 6 100 Shortcircuit 100 Shortcircuit Stop alarm Stop alarm
on alcomio on alcomio
node ... node ...
6 6 101 Alcom write 101 Alcom write Deviation Deviation
error ... node error ... node
... sub ... sub
6 6 102 Alcom 102 Alcom Deviation Deviation
message message
invalid node invalid node
... ...
6 6 103 Bad format 103 Bad format Deviation Deviation
on alcom on alcom
message message
6 6 104 Vmsio 104 Vmsio Stop alarm Stop alarm
interupt (...) interupt (...)
6 6 105 Invalid 105 Invalid Stop alarm Stop alarm
alcom bus alcom bus
number ... number ...
6 6 106 Lost token 106 Lost token Deviation Deviation
on alcomio on alcomio
node node
6 6 107 Vmslo board 107 Vmslo board Deviation/St- Deviation/St-
generated generated op alarm op alarm
reset!! reset!!
6 6 108 VmsIO pic 108 VmsIO pic Stop alarm Stop alarm
has wrong has wrong
version !! version !!
6 6 109 VmsIo board 109 VmsIo board Stop alarm Stop alarm
wrong wrong
version is ... version is ...
!! !!
6 6 110 Unexpected 110 Unexpected User User
sensor sensor notification notification
status node status node
... 0f sub ... 0f ... 0f sub ... 0f
6 6 111 I/O blocked 111 I/O blocked User User
notification notification
2007-12-18
DeLaval voluntary milking system VMS
Type Type Meaning Meaning
One of the ALCOM I/O boards has One of the ALCOM I/O boards has
been reset. been reset.
The system will repond by The system will repond by
activating all ALCOM I/O boards. activating all ALCOM I/O boards.
One of the ALCOM I/O boards has One of the ALCOM I/O boards has
an output that takes too much an output that takes too much
current, which could be a caused current, which could be a caused
by a short-circuit. The board will by a short-circuit. The board will
automatically protect itself by automatically protect itself by
setting all I/O to input until it has setting all I/O to input until it has
been reset. been reset.
An transmission error has occurred An transmission error has occurred
on the ALCOM bus. on the ALCOM bus.
The received ALCOM message The received ALCOM message
was incorrect. was incorrect.
ALCOM message is in an invalid ALCOM message is in an invalid
format. format.
The VMS I/O board has generated The VMS I/O board has generated
an unexpected interrupt. an unexpected interrupt.
Software error. Software error.
Communication error on the Communication error on the
ALCOM bus. ALCOM bus.
Reset on VMS I/O board, either Reset on VMS I/O board, either
because someone pressed the because someone pressed the
reset button or because of reset button or because of
electrical disturbances. electrical disturbances.
Note: a single reset will generate a Note: a single reset will generate a
Deviation only. Deviation only.
Microprocessor on VMS I/O board Microprocessor on VMS I/O board
has wrong program version. has wrong program version.
Wrong version of FPGA on VMS Wrong version of FPGA on VMS
I/O board. I/O board.
Some sensors in the Milk sampler Some sensors in the Milk sampler
indicate a problem in moving the indicate a problem in moving the
runner to the correct sample runner to the correct sample
position. position.
Some actuator has been blocked Some actuator has been blocked
by some signal. by some signal.
Troubleshooting
Communication and data transmission
between the milking station and
peripheral units (VMS I/O-man) - major
code 6
Action Action
If problem occurs frequently, contact If problem occurs frequently, contact
service engineer. service engineer.
Restart the milking station. Restart the milking station.
If the problem persists, contact service If the problem persists, contact service
engineer. engineer.
If problem occurs frequently, contact If problem occurs frequently, contact
service engineer. service engineer.
If problem occurs frequently, contact If problem occurs frequently, contact
service engineer. service engineer.
If problem occurs frequently, contact If problem occurs frequently, contact
service engineer. service engineer.
If problem occurs frequently, contact If problem occurs frequently, contact
service engineer. service engineer.
If problem occurs frequently, contact If problem occurs frequently, contact
service engineer. service engineer.
If problem occurs frequently, contact If problem occurs frequently, contact
service engineer. service engineer.
Restart the milking station. Restart the milking station.
If the problem occurs frequently, contact If the problem occurs frequently, contact
service engineer. service engineer.
Contact service engineer. Contact service engineer.
Service engineer only: Change Service engineer only: Change
microprocessor or reprogram it. microprocessor or reprogram it.
Contact service engineer. Contact service engineer.
Service engineer only: This can only Service engineer only: This can only
happen if the VMS I/O board has been happen if the VMS I/O board has been
changed to the wrong type. changed to the wrong type.
Replace IC103 from the removed board and Replace IC103 from the removed board and
place it on the installed board. place it on the installed board.
Check the Milk sampler and make sure that Check the Milk sampler and make sure that
the runner can move smoothly. the runner can move smoothly.
This is only for information. This is only for information.
94897201.pdf
186(198)