Subscribe to Our Youtube Channel
Related Manuals for DeLaval VMS 2012 Series
Summary of Contents for DeLaval VMS 2012 Series
- Page 1 Milk sampler (VMS 2012) © DeLaval 2012. 2012-01-10, Version 1 86352801 Original instruction...
-
Page 3: Table Of Contents
2.2 Starting a sampling sequence................7 2.3 Stopping a sampling sequence................. 10 Operators maintenance........................11 1 About carrying out maintenance..................11 1.1 Manual cleaning....................11 2 Additional maintenance..................... 13 2.1 Changing hoses....................13 © DeLaval 2012. 2012-01-10, Version 1 3 (18) 86352801... -
Page 4: Version 1
Milk sampler (VMS 2012) Table of contents © DeLaval 2012. 2012-01-10, Version 1 4 (18) 86352801... -
Page 5: Operation
DelPro soft- ware. 2 Collecting milk samples There are three main steps when collecting milk samples: Connecting the milk sampler Starting a sampling sequence Stopping a sampling sequence © DeLaval 2012. 2012-01-10, Version 1 5 (18) 86352801... -
Page 6: Connecting The Milk Sampler
4. Attach the milk hose to the milk pump con- nection on the milk pump. 5. Connect the electrical cable to the ALCOM bus connector (B) on the control box (A). A Control box B ALCOM bus connector © DeLaval 2012. 2012-01-10, Version 1 6 (18) 86352801... -
Page 7: Starting A Sampling Sequence
When the milk sampler has not been used more than three days it may need to be cleaned before being used again. That is why the sampling sequence is normally started just before a system cleaning. © DeLaval 2012. 2012-01-10, Version 1 7 (18) 86352801... - Page 8 Note! Make sure to check the settings for milk sampling in the management software (VC con- figuration) before starting a sampling sequence. For further information, see the DeLaval DelPro software, VMS (Help file). Sampling is performed by using the touch screen.
- Page 9 “131”. Use the Cancel button when typing the wrong number. 5. Press Ok 6. Press the Start button to start the sampling. © DeLaval 2012. 2012-01-10, Version 1 9 (18) 86352801...
-
Page 10: Stopping A Sampling Sequence
(A). Make sure that the runner is clean. 5. Check the silicone tubes for damage. A Control box cover B Sample tray C Sample compartment D Runner at zero point © DeLaval 2012. 2012-01-10, Version 1 10 (18) 86352801... -
Page 11: Operators Maintenance
VMS. If any parts such as a silicone hose has been damaged or deteriorated, additional mainte- nance will be needed. 1.1 Manual cleaning Tools: Syringe without needle. © DeLaval 2012. 2012-01-10, Version 1 11 (18) 86352801... - Page 12 Finally, rinse again with water to remove detergent. 5. Reconnect the hoses onto the container. Note! It is important not to shorten the hoses too much if they have been deterio- rated. © DeLaval 2012. 2012-01-10, Version 1 12 (18) 86352801...
-
Page 13: Additional Maintenance
The three hoses (A and B) must be changed if they have been deteriorated or if they not can be cleaned properly. Due to the complicated opera- tion, only the hose changing on the tube wheel has been described. © DeLaval 2012. 2012-01-10, Version 1 13 (18) 86352801... -
Page 14: Delaval
Changing the silicone hose on the tube wheel 1. Lift the sample tube (A) that is inserted in the runner. A Sample tube 2. Remove the silicon hose from the sample tube and hold the silicone hose. © DeLaval 2012. 2012-01-10, Version 1 14 (18) 86352801... - Page 15 7. Push the silicone hose through the hole in the wheel. 8. Allow the spring to rewind the silicone hose on to the wheel. A Silicon hose 9. Reinsert the sample tube into the silicone hose. © DeLaval 2012. 2012-01-10, Version 1 15 (18) 86352801...
- Page 16 Milk sampler (VMS 2012) Operators maintenance 10.Check that about 250 mm of the tube pro- trudes from the hole in the wheel. 250 mm © DeLaval 2012. 2012-01-10, Version 1 16 (18) 86352801...
- Page 17 Tetra Laval Holdings & Finance S. A. and DeLaval is a registered trade/service mark of DeLaval Holding AB.
- Page 18 DeLaval www.delaval.com Box 39 SE-147 21 Tumba SWEDEN...
Need help?
Do you have a question about the VMS 2012 Series and is the answer not in the manual?
Questions and answers