DeLaval VMS 2008 Instruction Book page 192

M M m m Alarm text Alarm text
5 5 126 Did not get 126 Did not get Stop alarm Stop alarm
water from water from
RA-unit RA-unit
within... within...
minutes minutes
5 5 127 Both low and 127 Both low and Stop alarm Stop alarm
high sensor high sensor
in receiver in receiver
active active
5 5 128 Timeout 128 Timeout Stop alarm Stop alarm
changing changing
milk filter milk filter
5 5 129 Milk diverted 129 Milk diverted Notfication Notfication
due to MDi, due to MDi,
dest %...f dest %...f
5 5 200 Timeout 200 Timeout User User
filling filling notication notication
detergent detergent
number %...f number %...f
5 5 201 Timeout 201 Timeout Stop alarm Stop alarm
filling water filling water
in step %...f, in step %...f,
substep %...f substep %...f
5 5 202 Timeout 202 Timeout Stop alarm Stop alarm
empting empting
water in step water in step
%.0f, %.0f,
substep %.0f substep %.0f
5 5 203 Too low 203 Too low Deviation Deviation
temp at temp at
filling filling
%T.0%.0f %T.0%.0f
min min
%T.0%.0f %T.0%.0f
5 5 204 Too low 204 Too low Deviation Deviation
temp after temp after
circulation circulation
%T...%...f %T...%...f
min min
%T...%...f %T...%...f
5 5 205 Invalid 205 Invalid Stop alarm Stop alarm
cleaning cleaning
config. config.
2007-12-18
DeLaval voluntary milking system VMS
Type Type Meaning Meaning
Water that should be delivered Water that should be delivered
from "ReceiveAll" equipment did from "ReceiveAll" equipment did
not became available within time. not became available within time.
ReceiveAll is optional, only used at ReceiveAll is optional, only used at
some installations. Cleaning will be some installations. Cleaning will be
aborted automaticly. aborted automaticly.
Level sensor in receiver indicated Level sensor in receiver indicated
both high and low level at the both high and low level at the
same time. same time.
If change of milk filter was started If change of milk filter was started
but not completed within time this but not completed within time this
alarm will be given. alarm will be given.
See alarm text. See alarm text.
The configured amount of The configured amount of
detergent was not pumped to detergent was not pumped to
charging vessel within time. charging vessel within time.
Cleaning is continued anyhow. Cleaning is continued anyhow.
Charge vessel was not filled within Charge vessel was not filled within
time. time.
Note! If the charge vessel was not Note! If the charge vessel was not
empty when starting to fill water empty when starting to fill water
this alarm could be generated at this alarm could be generated at
start of filling. start of filling.
The water level in receiver does The water level in receiver does
not affect the upper level indicator not affect the upper level indicator
(EndUnitHighLevel is not reached), (EndUnitHighLevel is not reached),
when sucking water from washing when sucking water from washing
trough into receiver. trough into receiver.
Water temperature at filling charge Water temperature at filling charge
vessel is too low. vessel is too low.
The return water temperature is The return water temperature is
measured at end of circulation measured at end of circulation
cleaning. If this temperature is cleaning. If this temperature is
below limit set in cleaner below limit set in cleaner
configuration the alarm will be configuration the alarm will be
generated. generated.
Cleaning procedure will not start. Cleaning procedure will not start.
Troubleshooting
Action Action
Try to find out why water was not available. Try to find out why water was not available.
Call serviceman if problem remains. Call serviceman if problem remains.
Call service technician if several alarms. Call service technician if several alarms.
Sensor should be checked. Sensor should be checked.
Make sure the filter change operation is Make sure the filter change operation is
completed. completed.
Check the cows that caused the notification. Check the cows that caused the notification.
Depending on the strategy at the farm the Depending on the strategy at the farm the
thresholds can be changed. Lowering the thresholds can be changed. Lowering the
thresholds will increase the thresholds will increase the
diversion/notifications while increasing the diversion/notifications while increasing the
threshold will decrease the number of threshold will decrease the number of
diversions/notifications. The thresholds are diversions/notifications. The thresholds are
changed in Animal>VMS Cow>Automatic changed in Animal>VMS Cow>Automatic
diversion. diversion.
Make sure that there is detergent in the Make sure that there is detergent in the
container. Check that the hoses are container. Check that the hoses are
connected to the pump. If the problem connected to the pump. If the problem
remains call a serviceman. remains call a serviceman.
Check water pressure, check filters or Check water pressure, check filters or
strainers in the waterline! Check the water strainers in the waterline! Check the water
valves! Make sure that the charge vessel is valves! Make sure that the charge vessel is
empty before being refilled. Check the level empty before being refilled. Check the level
sensor. If the problem remains call a sensor. If the problem remains call a
serviceman. serviceman.
Check vacuum system, check connections Check vacuum system, check connections
between all 5 teat cups and their jetters. between all 5 teat cups and their jetters.
(Did you receive "teat cup not tight to jetter" (Did you receive "teat cup not tight to jetter"
message?) If "EndUnitHighLevel" is message?) If "EndUnitHighLevel" is
positioned too high, this alarm could be positioned too high, this alarm could be
generated. If the problem remains call a generated. If the problem remains call a
serviceman. serviceman.
Note this temperature check is only done Note this temperature check is only done
when using hot water. Check boiler, check when using hot water. Check boiler, check
set point setting in cleaner configuration. set point setting in cleaner configuration.
Check temperature sensor. If the problem Check temperature sensor. If the problem
remains call a serviceman. remains call a serviceman.
Check same at alarm 5:203. If the Check same at alarm 5:203. If the
installation has long not insulated transport installation has long not insulated transport
lines the temperature fall could be too big. lines the temperature fall could be too big.
Check for residual pre-rinse water (purge Check for residual pre-rinse water (purge
problem). problem).
Call for service engineer. Call for service engineer.
94897201.pdf
184(198)