Table of Contents
Advertisement
EN
The humidity sensor WX325 measures
•
temperature and relative humidity.
Weight 175 g with leads (ca 4 m)
•
Dimensions: 51 mm x 73 mm x 27 mm
•
1.3. Troubleshooting
If an error occurs, the heater and/or steamer power
will cut off and the control panel will show an error
message "E (number)", which helps troubleshooting
the cause for the error. Table 1.
Note! All service operations must be done by
professional maintenance personnel. No user-
serviceable parts inside.
Description/ Popis
E1
Temperature sensor's measuring
circuit broken.
Teplotni cidlo je rozbite.
E2
Temperature sensor's measuring
circuit short-circuited.
Merici elektronika cidla se zacyklila. Podivejte se na cervene a zlute vodice k teplotnimu cidlu
E3
Overheat protector's measuring
circuit broken.
Ochrana proti prehrati je rozbita. Stisknete tlacitko reset ( viz bod 3.5)
E6
Humidity sensor's temperature
measuring component failure.
Vlhkostni cidlo je poskozene.
E7
Humidity sensor's humidity
measuring component failure.
Vlhkostni cidlo je poskozene.
E8
Humidity sensor's humidity
measuring circuit broken.
Obvody cidla vlhkosti jsou rozbite.
E9
Connection failure between the
control panel and the power unit.
Spojeni mezi panelem a
powerboxem nefunguje.
Water level low or steamer's
overheat protector engaged.
Water level warning light blinks.
Nizka uroven vody v nadrzce
nebo sepnuta ochrana
proti prehrati. Blika kontrolka.
Tabulka 1.
Error messages. Note! All service operations must be done by professional maintenance personnel.
Chybové zpravy. Pozor! Vsechny servisni ukony musi provadet vyskoleny personal
4
NTC-Termistor
(22 k Ω /T=25 °C).
Vlhkostni cidlo WX325
•
Vaha 175 g a kabel (ca 4 m)
•
Rozmery: 51 mm x 73 mm x 27 mm
•
1.3. Reseni problemu
Objevi-li se chyba, napajení topidla se
odpoji a ovladaci panel ukaze chybove
hlasení „E (cislo)". Toto chybove hlaseni
pomuze urcit pricinu. Viz. Tabulka 1
Pozor! Vsechny servisni operace musi
provadet kvalifikovany personal.
Zarizení neobsahuje zadné casti,
ktere by bezný uzivatel mohl opravit.
Oprava
Check the red and yellow wires to the temperature sensor and their
connections (see figures 6 and 7) for faulties.
Podivejte se na cervene a zlute vodice k teplotnimu cidlu
a jejich spojeni - ( viz obr. 6 a 7 )
Check the red and yellow wires to the temperature sensor and their
connections (see figures 6 and 7) for faulties.
a jejich spojeni - ( viz obr. 6 a 7 )
Press the overheat protector's reset button (see section 3.5.).
Check the blue and white wires to the temperature sensor and their
connections (see figures 6 and 7) for faulties.
Podivejte se na modre a bile draty pro teplotni
cidlo a jejich spojeni ( viz obr. 6 a 7 )
Check the brown and blue wires to the humidity sensor and their
connections (see figures 6 and 7) for faulties. Replace the sensor.
Zkontrolujte hnede a modre draty k cidlu vlhkosti
a jejich spojeni ( viz obr. 6 a 7 ) . Vymente cidlo.
Check the brown and blue wires to the humidity sensor and their
connections (see figures 6 and 7) for faulties. Replace the sensor.
Zkontrolujte hnede a modre draty k cidlu vlhkosti
a jejich spojeni ( viz obr. 6 a 7 ) . Vymente cidlo.
Check the brown and blue wires to the humidity sensor and their
connections (see figures 6 and 7) for faulties.
Zkontrolujte hnede a modre draty k cidlu vlhkosti
a jejich spojeni ( viz obr. 6 a 7 ) . Vymente cidlo.
Check the cable and the connectors.
Zkontrolujte kabely a konektory.
Add water (manual filling models) or check the water supply
(automatic filling models). Check the steamer's overheat protector.
See the steamer's or Combi heater's manual for more instructions and
safety information.
Pridejte vodu ( manualni modely ) nebo zkontrolujte privod vody
(automaticke modly) Zkontrolujte tepelnou ochranu vyparniku .
Podivejte se do manualu kamen o tomto stavu kamen
Advertisement
Table of Contents
