Table of Contents
Advertisement
EN
Basic mode (heater and steamer on)
The top row shows the sauna room
temperature. The bottom row shows the
humidity level (or remaining on-time, if the
steamer is not activated).
Example: the heater will start after 10 minutes.
Basic mode (pre-setting time running,
heater and steamer off)
The decrease of remaining pre-setting time
is shown until zero appears, after which the
activated devices (heater and/or steamer)
are switched on. The bottom row shows the
remaining pre-setting time.
Figure 3a.
Settings menu structure, basic settings
Obrazrk 3a.
Struktura nastaveni menu, zakladni nastaveni.
BASIC SETTINGS/ZAKLADNI NASTAVENI
Press the MENU button to open the set-
tings menu.
Sauna room temperature (shown if
the heater is activated)
The display shows the sauna room tem-
perature setting. Temperature indicator
light blinks.
Change the setting to the desired tem-
•
perature with the – and + buttons.
The sum of temperature and humidity
•
can be 140 at maximum (see chapter
2.2.)
Press the MENU button to access the
next setting.
Sauna room humidity level (shown if
the steamer is activated)
The display shows the sauna room hu-
midity setting. Humidity indicator light
blinks.
Change the setting to the desired hu-
•
midity with the – and + buttons.
The sum of temperature and humidity
•
can be 140 at maximum (see chapter
2.2.)
Press the MENU button to access the
next setting.
Remaining on-time
Press the – and + buttons to adjust the
remaining on-time.
Example: the heater will be on for 3 hours
and 40 minutes.
Pre-setting time (timed switch-on)
Press the + button until you overstep
•
the maximum on-time. Temperature
and humidity indicator lights switch
off. Pre-setting time symbol blinks on
the screen.
Select the desired pre-setting time
•
using the – and + buttons. The time
changes in 10 minute steps.
Press the MENU button to exit.
Zakladni moc (kamna a vyparnik zapnuty)
Horni radek ukazuje teplotu
v saune. Spodni radek ukazuje
vlhkost sauny nebo cas pokud je
vyparnik vypnuty.
Po stisnuti MENU se otevre
menu nastaveni.
Teplota sauny ( je zobrazena
pokud jsou kamna sepnuta )
Displej ukazuje nastaveni teploty.
Kontrolka teploty blika.
Zmenu teploty provadite tlacitky "-" a "+"
Celkova hodnota teploty a vlhkosti
nesmi presahnout 140 - viz kapitola 2.2.
Dalsim stiskem menu se dostanete
na dalsi nastaveni.
Vlhkost sauny ( je zobrazena
pokud je vyparnik sepnut )
Displej ukazuje nastaveni vlhkosti.
Kontrolka vlhkosti blika.
Zmenu teploty provadite tlacitky "-" a "+"
Celkova hodnota teploty a vlhkosti
nesmi presahnout 140 - viz kapitola 2.2.
Dalsim stiskem menu se dostanete
na dalsi nastaveni.
Nastaveni casu
Tlacitky "+" a "-" si nastavujete
cas jak dlouho saunu bude sepnuta.
Priklad: Sauna pojede 3 hodiny a 40 minut
Prednastaveni casu
Pri mackani tlacitka + az na maximalni teplotu
a zobrazi se displej tak jak vidite na obrazku.
Kontrolky prestanou blikat
Pak tlacitky + a - nastavime cas za jak dlouho
chceme aby se sauna sepla.
Priklad: Kamna se sepnou za 10 minut.
Dalsim stiskem MENU se
dostaneme do zakladniho rezimu.
Zakladni mod ( prednastaveni casu bezi
kamna a vyparnik jsou vypnuty)
Odpocitavani prednastaveni bezi
po zobrazeni 0 se kamna a vyparnik zapnou
a na spodnim radku se zobrazi nastaveny cas.
7
7
Advertisement
Table of Contents
