Mitsubishi Electric FR-F820-00046 Instruction Manual page 20

Parameter list
Setting
Pr. Name
Modbus-RTU
0 to 999.8s,
539 communication check
9999
time interval
USB communication
547 0 to 31
station number
USB communication check
548 0 to 999.8s, 9999
time interval
549 Protocol selection 0, 1, 2
NET mode operation
550 command source 0, 1, 9999
selection
PU mode operation
551 command source 1 to 3, 9999
selection
552 Frequency jump range 0 to 30Hz, 9999
553 PID deviation limit 0 to 100%, 9999 9999
PID signal operation
554 0 to 3, 10 to 13
selection
555 Current average time 0.1 to 1.0s
556 Data output mask time 0 to 20s
Current average value 0 to 500A
557 monitor signal output
0 to 3600A
reference current
Second frequency search 0 to 32767,
560
gain 9999
PTC thermistor protection 0.5 to 30kΩ,
561
level 9999
Energization time
563 (0 to 65535)
carrying-over times
Operating time
564 (0 to 65535)
carrying-over times
Second motor speed
569 0 to 200%, 9999 9999
control gain
570 Multiple rating setting 0, 1
571 Holding time at a start 0 to 10s, 9999
4 mA input check
573 1 to 4, 9999
selection
Second motor online
574 0, 1
auto tuning
Output interruption
575 0 to 3600s, 9999 1s
detection time
Output interruption
576 0 to 590Hz
detection level
Output interruption
577 900 to 1100%
cancel level
Auxiliary motor
578 0 to 3
operation selection
Motor connection
579 0 to 3
function selection
MC switching interlock
580 0 to 100s
time
581 Start waiting time 0 to 100s
Auxiliary motor
582 connection-time 0 to 3600s, 9999 1s
deceleration time
Auxiliary motor
583 disconnection-time 0 to 3600s, 9999 1s
acceleration time
Auxiliary motor 1
584 0 to 590Hz
starting frequency
Auxiliary motor 2
585 0 to 590Hz
starting frequency
Auxiliary motor 3
586 0 to 590Hz
starting frequency
Auxiliary motor 1
587 0 to 590Hz
stopping frequency
Auxiliary motor 2
588 0 to 590Hz
stopping frequency
Auxiliary motor 3
589 0 to 590Hz
stopping frequency
Auxiliary motor start
590 0 to 3600s
detection time
Auxiliary motor stop
591 0 to 3600s
detection time
Traverse function
592 0 to 2
selection
Maximum amplitude
593 0 to 25%
amount
Amplitude
594 compensation amount 0 to 50%
during deceleration
Amplitude
595 compensation amount 0 to 50%
during acceleration
Amplitude acceleration
596 0.1 to 3600s
time
Amplitude deceleration
597 0.1 to 3600s
time
350 to 430V,
598 Undervoltage level

9999
X10 terminal input
599 0,1
selection
First free thermal
600 0 to 590Hz, 9999 9999
reduction frequency 1
First free thermal reduction
601 1 to 100%
ratio 1
20
DRIVE THE MOTOR
Initial
Pr.
range value
First free thermal
602
9999 reduction frequency 2
First free thermal reduction
603
ratio 2
0
First free thermal
604
reduction frequency 3
9999
Power failure stop
0 606 external signal input
selection
9999 Motor permissible load
607
level
Second motor
608
9999 permissible load level
PID set point/deviation
609
9999 input selection
PID measured value
610
input selection
0
Acceleration time at a
611
restart
1s
Speed smoothing
0s
653
control
LD/SLD

Speed smoothing cutoff
rated inverter
654
frequency

current

Analog remote output
655
9999
selection
656 Analog remote output 1
9999
657 Analog remote output 2
658 Analog remote output 3
0
659 Analog remote output 4
Increased magnetic
0
660 excitation deceleration
operation selection
Magnetic excitation
661
1/0 increase rate

9999 Increased magnetic
662 excitation current level 0 to 300%
9999
Regeneration
665 avoidance frequency
0
gain
Power failure stop
668
frequency gain
SF-PR slip amount
0Hz 673 adjustment operation
selection
1000%
SF-PR slip amount
674
adjustment gain
0
Tuning data unit
684
switchover
0
686 Maintenance timer 2
Maintenance timer 2
687
1s
warning output set time
688 Maintenance timer 3
1s
Maintenance timer 3
689 warning output set time 0 to 9998, 9999 9999
Second free thermal
692
reduction frequency 1
Second free thermal
693
reduction ratio 1
Second free thermal
60/50Hz 694

reduction frequency 2
Second free thermal
60/50Hz 695

reduction ratio 2
Second free thermal
60/50Hz 696

reduction frequency 3
699 Input terminal filter
0Hz
Maximum motor
702
frequency
0Hz
Induced voltage
706
constant (phi f)
0Hz
707 Motor inertia (integer)
711 Motor Ld decay ratio
5s
712 Motor Lq decay ratio
5s
Starting resistance tuning
717
compensation
0
Starting magnetic pole
721 position detection pulse
10% width
724 Motor inertia (exponent)
Motor protection current
10%
725
level
Auto Baudrate/Max
726
Master
10%
727 Max Info Frames
Device instance
5s
728
number (Upper 3 digits)
Device instance
5s
729 number (Lower 4 digits) 0 to 9999
Second motor induced
9999
738
voltage constant (phi f)
Second motor Ld decay
0
739
ratio
Second motor Lq decay
740
ratio
Second starting
100%
741 resistance tuning
compensation
Setting Initial
Name
range value
0 to 590Hz, 9999 9999
1 to 100% 100%
0 to 590Hz, 9999 9999
0, 1 1
110 to 250% 150%
110 to 250%,
9999
9999
1 to 5 2
1 to 5, 101 to 105 3
0 to 3600s, 9999 9999
0 to 200% 0
0 to 120Hz 20Hz
0, 1, 10, 11 0
1000%
1000%
800 to 1200%
1000%
1000%
0, 1 0
0 to 40%, 9999 9999
100%
0 to 200% 100%
0 to 200% 100%
2, 4, 6, 9999 9999
0 to 500% 100%
0, 1 0
0(1 to 9998) 0
0 to 9998, 9999 9999
0(1 to 9998) 0
0 to 590Hz, 9999 9999
1 to 100% 100%
0 to 590Hz, 9999 9999
1 to 100% 100%
0 to 590Hz, 9999 9999
5 to 50ms, 9999 9999
0 to 400Hz, 9999 9999
0 to 5000mV/
9999
(rad/s), 9999
10 to 999, 9999 9999
0 to 100%, 9999 9999
0 to 100%, 9999 9999
0 to 200%, 9999 9999
0 to 6000μs,
10000 to 9999
16000μs, 9999
0 to 7, 9999 9999
100 to 500%,
9999
9999
0 to 255 255
1 to 255 1
0 to 419 0
0
0 to 5000mV/
9999
(rad/s), 9999
0 to 100%, 9999 9999
0 to 100%, 9999 9999
0 to 200%, 9999 9999
Setting
Pr. Name
range
0 to 6000μs,
Second motor magnetic
742 10000 to
pole detection pulse width
16000μs, 9999
Second motor 0 to 400Hz,
743
maximum frequency 9999
Second motor inertia
744 10 to 999, 9999 9999
(integer)
Second motor inertia
745 0 to 7, 9999
(exponent)
Second motor
746 protection current level 100 to 500%, 9999 9999
0, 10, 11, 20, 21,
50, 51, 60, 61,
70, 71, 80, 81,
90, 91, 100,
Second PID action
753 101, 1000,
selection
1001, 1010,
1011, 2000,
2001, 2010,
2011
Second PID control
754 automatic switchover 0 to 590Hz, 9999 9999
frequency
Second PID action set
755 0 to 100%, 9999 9999
point
Second PID 0.1 to 1000%,
756
proportional band 9999
Second PID integral 0.1 to 3600s,
757
time 9999
Second PID differential 0.01 to 10.00s,
758
time 9999
759 PID unit selection 0 to 43, 9999
Pre-charge fault
760 0, 1
selection
761 Pre-charge ending level 0 to 100%, 9999 9999
0 to 3600s,
762 Pre-charge ending time
9999
Pre-charge upper detection
763 0 to 100%, 9999 9999
level
764 Pre-charge time limit 0 to 3600s, 9999 9999
Second pre-charge fault
765 0, 1
selection
Second pre-charge
766 0 to 100%, 9999 9999
ending level
Second pre-charge 0 to 3600s,
767
ending time 9999
Second pre-charge
768 0 to 100%, 9999 9999
upper detection level
Second pre-charge time
769 0 to 3600s, 9999
limit
Operation panel monitor 1 to 3, 5 to 14, 17,
774
selection 1 18, 20, 23 to 25,
34, 38, 40 to 45,
Operation panel monitor
775
50 to 57, 61, 62,
selection 2
64, 67, 68,
Operation panel monitor
81 to 96, 98,100,
776
selection 3 9999
4 mA input fault
777 0 to 590Hz, 9999 9999
operation frequency
778 4 mA input check filter 0 to 10s
Operation frequency
779 during communication 0 to 590Hz, 9999 9999
error
Acceleration time in
791 0 to 3600s, 9999 9999
low-speed range
Deceleration time in
792 0 to 3600s, 9999 9999
low-speed range
Pulse increment setting 0.1, 1, 10, 100,
799
for output power 1000kWh
Control method
800 9, 20
selection
820 Speed control P gain 1 0 to 1000%
Speed control integral
821 0 to 20s
time 1
822 Speed setting filter 1 0 to 5s, 9999
Torque control P gain 1
824 (current loop 0 to 500%
proportional gain)
Torque control integral
825 time 1 (current loop 0 to 500ms
integral time)
827 Torque detection filter 1 0 to 0.1s
828 Parameter for manufacturer setting. Do not set.
830 Speed control P gain 2 0 to 1000%, 9999 9999
Speed control integral
831 0 to 20s, 9999
time 2
832 Speed setting filter 2 0 to 5s, 9999
834 Torque control P gain 2 0 to 500%, 9999 9999
Torque control integral
835 0 to 500ms, 9999 9999
time 2
837 Torque detection filter 2 0 to 0.1s, 9999 9999
Analog input offset
849 0 to 200%
adjustment
Terminal 4 function
858 0, 4, 9999
assignment
Initial
value
9999
9999
9999
0
100%
1s
9999
9999
0
9999
0
9999
9999
9999
9999
9999
0s
1kWh
20
25%
0.333s
9999
50%
40ms
0s
9999
9999
100%
0