ABB i-bus 6108/18-BS-500 Technical Reference Manual page 93

Setpoint adjustment ............................................................. 59
Setpoint adjustment - Maximum manual increase during
cooling mode (0 - 15°C) ................................................. 60
Setpoint adjustment - Maximum manual increase during
heating mode (0 - 15°C) ................................................. 59
Setpoint adjustment - Maximum manual reduction during
cooling mode (0 - 15°C) ................................................. 60
Setpoint adjustment - Maximum manual reduction during
heating mode (0 - 15°C) ................................................. 59
Setpoint adjustment - Permanent storage of on-site operation
........................................................................................ 61
Setpoint adjustment - Resetting of the manual adjustment for
receipt of a basic setpoint ............................................... 60
Setpoint adjustment - Resetting the manual adjustment for
change of operating mode .............................................. 61
Setpoint adjustment - Resetting the manual adjustment via
object .............................................................................. 61
Setpoint display ................................................................... 87
Setpoint settings .................................................................. 55
Setpoint settings - Cyclic sending of the current set-point
temperature (min) ........................................................... 59
Setpoint settings - Display indicates .................................... 58
Setpoint settings - Hysteresis for switchover heating/cooling
........................................................................................ 56
Setpoint settings - Increase for ECO cooling (°C) ............... 58
Setpoint settings - Increase for standby cooling (°C) .......... 57
Setpoint settings - Reduction for ECO heating (°C) ............ 57
Setpoint settings - Reduction for standby heating (°C) ....... 56
Setpoint settings - Send current setpoint ............................. 59
Setpoint settings - Setpoint for heating comfort = setpoint for
cooling comfort ............................................................... 55
Setpoint settings - Setpoint temperature for cooling comfort
(°C) ................................................................................. 57
Setpoint settings - Set-point temperature for frost protection
(°C) ................................................................................. 57
Setpoint settings - Set-point temperature for heat protection
(°C) ................................................................................. 58
Setpoint settings - Setpoint temperature for heating and
cooling comfort (°C) ........................................................ 56
Setpoint settings - Setpoint temperature for heating comfort
(°C) ................................................................................. 56
Settings of basic load .......................................................... 53
Settings of basic load - Minimum control value for basic load
> 0 ................................................................................... 53
KNX Technical Reference Manual 1473-1-8914 / 2CKA001473B8914
Setup and function ...............................................................13
Software ...............................................................................20
Summer compensation ........................................................69
Summer compensation - (Lower) Starting temperature for
summer compensation (°C) ............................................70
Summer compensation - Offset of the set-point temperature
for the entry into summer compensation (x 0.1°C) .........70
Summer compensation - Offset of the set-point temperature
for the exit from summer compensation (x 0.1°C) ..........71
Summer compensation - Summer compensation ................69
Summer compensation active ..............................................86
Superimposed operating mode ............................................79
Switching On and Off ...........................................................25
Switchover heating/cooling ..................................................81
T
Target group ........................................................................10
Technical data ......................................................................16
Temperature display – Temperature unit .............................72
Temperature reading - Adjustment value for internal
temperature measurement (x 0.1°C) ..............................63
Temperature reading - Control value for fault (0 - 255) .......64
Temperature reading - Cyclic sending of actual temperature
(min) ................................................................................63
Temperature reading - Difference of value for sending the
actual temperature (x 0.1°C) ...........................................63
Temperature reading - Inputs of temperature reading .........61
Temperature reading - Inputs of weighted temperature
reading ............................................................................62
Temperature reading - Monitoring time for temperature
reading (0 = no monitoring) (min) ....................................63
Temperature reading - Operating mode for fault .................64
Temperature reading - Weighting of external measurement (0
to 100%) ..........................................................................62
Temperature reading - Weighting of external measurement 2
(0 to 100%) .....................................................................62
Temperature reading - Weighting of internal measurement (0
to 100%) ..........................................................................62
U
Update .................................................................................21
W
Window contact ....................................................................79
Index
│93