Danfoss VLT HVAC Basic Drive FC 101 Design Manual page 77

How to Program
At power up the user is
asked to choose the
prefered laguage.
Select language
[1] English
Setup 1
Status
Menu
1
Com.
On
Warn.
Alarm
Hand
Reset
On
Power Up Screen
The next screen will be
the Wizard screen.
Press OK to start Wizard
Press Back to skip it
Setup 1
Status
Menu
2
Com.
On
Warn.
Alarm
Hand
On
Wizard Screen
if
0.0 Hz
0.0 kW
Setup 1
3
Status
Menu
Com.
On
Warn.
Alarm
Hand
On
Status Screen
The Wizard can always be
reentered via the Quick Menu!
Wizard completed
Press OK to accept
38
Setup 1
0.0 Hz
39
0.0 kW
Setup 1
Figure 6.4 Open-loop Set-up Wizard
MG18C522
Design Guide
... the HVAC FC 101 Wizard starts
Main
Quick
PM motor
Menu
Menu
Set Motor current
12 3.8 A
Setup 1
OK
Select Motor nominal speed
3000
RPM
13
Setup 1
O
Auto
Set Motor Cont. Rated Torque
On
14
5.4
Nm
Setup 1
Stator resistance
15
0.65 Ohms
OK
Setup 1
Motor poles
16
8
Setup 1
Back EMF at 1000 rpm
17
57
V
Setup 1
d-axis inductance
18
5
mH
Setup 1
Main
Quick if OK
Menu Set Max Output Frequency
Menu
19
0065 Hz
Setup 1
OK
O
Auto
Reset
On
Main
Quick
Menu
Menu
Current
Set T53 Low Current
OK
04.66 A
28
Setup 1
Set T53 High Current
O
Auto
13.30 A
Reset On
29
Setup 1
(Do not AMA)
Auto Motor Adapt OK
Press OK
37
Setup 1
Danfoss A/S © Rev. 2014-01-14 All rights reserved.
Select Regional Settings
4
[0]
Power kW/50 Hz
Setup 1
Grid Type
5
[0] 200-240V/50Hz/Delta
Setup 1
Select Motor Type
6
[0] Asynchronous
Setup 1
Set Motor Power
1.50
kW
Setup 1
Set Motor Voltage
0050
V
Setup 1
Set Motor frequency
0050
Hz
Setup 1
Set Motor current
04.66
A
Setup 1
Set Motor nominal speed
1420
RPM
Setup 1
Set Motor Speed low Limit
0000
Hz
20
Setup 1
Set Motor Speed high Limit
21 0050 Hz
Setup 1
Set Ramp 1 ramp-up time
22
0003
s
Setup 1
Set Ramp 1 ramp-down Time
Motor Type = Asynchronous
0003 s
23
Setup 1
Active Flying start?
24 [0] Disable
Motor Type = PM Motor Setup 1
Select T53 Mode
25
[0] Current Voltage
Setup 1
Set T53 low Voltage
0050 V
Setup 1
Set T53 high Voltage
0220 V
Setup 1
Set Min Reference
0000 Hz
30
Setup 1
Set Max Reference
0050
31 Hz
Setup 1
Select Function of Relay 1
[0] No function
[0]
32
Setup 1
Select Function of Relay 2
33 [0] No function
Setup 1
Automatic Motor Adaption
34
[0]
O
Setup 1
Do AMA
AMA running
AMA Failed
35 36
-----
Setup 1
AMA OK AMA failed
Asynchronous Motor
7
8
9
10
11
26
27
6 6
75