FULTON Endura+ Series Installation And Operation Manual page 76

MAINTENANCE
Item Part Number Description
1 2-12-000012 3/4" NPT Sight Observation Port
2 2-12-000191 Loctite C5-A Copper Anti-seize
5 2-12-315003 029 1/16" AFLAS O-Ring 5/8" OD
7 2-12-315005 EDR+ 3000 Burner to PV Gasket
9 2-12-315007 EDR+ 3000 Premix to Burner Gasket
11 2-20-315100 EDR+3000 Spark Ignitiion Assembly
27 2-22-000156 3/8-16 NICu400 Hex Nut
31 2-22-000353
3/8" Belleville Washer (Inconel 718, .385" ID x 1.25" OD x .125 THK, .021" Dish)
36 2-22-315021 10-32 x 1/4" Long S.S. Torx Screw
73 2-40-000464 3/4" - 14 NPSM Thermal Barrier for Flame Detector
74 2-40-001107 Siemens LMV2-3 High Sensitivity UV Scanner
JOB NUMBER:
76 2-40-315000 EDR+3000 Burner
3/20/2017
92 2-45-315501 O2 Sensor
PROJECT NAME:
99 2-50-315111 EDR+3000 Premix Retainer Plate
3/20/2017
105 5-10-315300 EDR+2500/3000 Burner Volume Reducer/Premix Inlet Assembly
PROJECT MANAGER:
3/20/2017
74
73
APPLY PARKER SUPER-O-LUBE
5
DURING INSTALLATION
INCORPORATED ECR#'S; 2017-1513, 2017-1495,
4-8
C 2017-1487, 2017-1469, 2017-1462 AND
2017-1415. B.M.P. 8/28/2017
INCORPORATED ECR# 2017-1347.
B
B.M.P. 7/19/2017
Bill of Material
THIS DRAWING SUPERSEDES DRAWING NUMBER RD-7621
DESCRIPTION:
EDR+ 3000 FINAL ASSEMBLY
36 APPLY LOCTITE COPPER C5-A ANTI-SEIZE
11
(2-12-000191), & TORQUE TO 27 IN. LBS.,
(TYP. 2 PLCS.)
1
FIGURE 25 - EDR+ 2500/3000 BUR ER ASSEMBLY
BURNER / PREMIX ASSEMBLY
S.M. A.K. P.E.K. R.A.S. B.A.S.
9/6/17 8/29/17 8/29/17 8/29/17 8/30/17
S.M. A.K. P.E.K. R.A.S. B.A.S.
8/10/17 7/20/17 7/20/17 7/20/17 7/21/17
INSULATION INSTALLATION DETAIL
WASHER ORIENTATION DETAIL
(SHOWN PRETORQUE FOR CLARIFICATION)
SHEET 6 OF 9
APPLY LOCTITE COPPER C5-A ANTI-SEIZE (2-12-000191),
TIGHTEN 1.5 - 3.0 TURNS PAST FINGER TIGHT
This design and drawings
UNLESS OTHERWISE NOTED
The items shown in this
DIMENSIONS ARE IN INCHES
are proprietary and are the
drawing may be covered by
TOLERANCES
exclusive property of
FRACTION & 1/8
one or more patents of
WHOLE VALUE
Fulton Group N.A., Inc.
Fulton Group N.A., Inc.
(1) PLACE DEC. 0.03
The corporation does not
(2) PLACE DEC. 0.015
(3) PLACE DEC. 0.005
permit their use except
ANGLE 0.5 DEG
with prior written consent.
SURFACE FINISH
250 MICRO-INCHES
EDRP-IOM-2019-0212
BELLEVILLE WASHERS MUST BE INSTALLED
IN THE ORIENTATION SHOWN.
31
Fulton Group N.A., Inc
972 Centerville Road
Pulaski, New York USA 13142
DRAWING NUMBER
7-91-315300
TORQUE TO 26-33 FT. LBS .
92
APPLY LOCTITE C5-A COPPER ANTI-SEIZE (2-12-000191) TO
THREADS WHEN INSTALLING 02 BYPASS TUBE. FULLY INSERT
TUBE INTO FITTING, TIGHTEN THE NUT UNTIL THE TUBE
WILL NOT TURN OR MOVE AXIALLY. THEN TIGHTEN
FITTING 1 1/4 MORE REVOLUTIONS
27 31 2
(2 PC.)
99
105
9 BE SURE THE CORRECT GASKET AND
ORIENTATION IS USED AT THIS LOCATION
76
7 BE SURE THE CORRECT GASKET AND
ORIENTATION IS USED AT THIS LOCATION
DRAWN BY: MECH. ENG:
M.A. / B.M.P. 9/28/2016 P.E.K. 3/20/2017
© Fulton Group N.A., Inc. 2019
CHECKED BY: ELEC. ENG:
T.T. 3/23/2017 A.M.K. 3/20/2017
B.O.M. REVIEW APPROVED BY:
SECTION 4
REV
C
ITEM
1
2
5
7
9
11
27
31
36
73
74
76
92
99
105
APPLY LOCTITE C5-A COPPER ANTI-SEIZE
(2-12-000191), & TORQUE TO 23 FT. LBS.
(SEE WASHER ORIENTATION DETAIL VIEW
FOR PROPER BELLEVILLE WASHER
INSTALLATION, (TYP. 12 PLCS.)
THIS DRAWING SUPERSEDES DRAWI
JOB NUMBER: DESCRIPTION:
EDR+ 3000 FINAL ASSEM
PROJECT NAME:
PROJECT MANAGER:
PART
2-12-
2-12-
2-12-
2-12-
2-12-
2-20-
2-22-
2-22-
2-22-
2-40-
2-40-
2-40-
2-45-
2-50-
5-10-