Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hored PS3016S
Summary of Contents for Hored PS3016S
- Page 1 User Manual PS3016S 16 Port Layer2 Managed PoE Switch...
- Page 2 Installation manual introduction The Product installation manual mainly describes PS1016S PoE switch hardware features, installation methods, and precautions during the installation This manual includes the following chapters: Chapter 1: Product Introduction. Briefly describes the basic features of the switch and the appearance details.
-
Page 3: Chapter 1 Product Introduction
Chapter 1 Product Introduction 1.1Product introduction PS3016S is managed PoE switch for security transmission and WIFI coverage, meet the WIFI AP, IP-camera, WIFI bridge, IP phones and other types of equipment PoE power supply needs. Products using a new generation of high-performance... -
Page 4: Front Panel
1.3Appearance ◼ Front Panel Including indicators, RJ45 port, shortcut buttons, RST button, SFP port, CONSOLE port, as shown in below ◼ Indicators PS3016S The indicator working status is shown as the following table Indicator Work Title Color Description status Solid... -
Page 5: Back Panel
SFP1, SFP2 form a Combo port. At the same time Combo port two ports can only use one. Two Combo port shared 17, 18 Indicator light SFP Port PS3016S provide 2 Combo Gigabit SFP optical ports (SFP1, SFP2), can be inserted into the Gigabit SFP module RST Button ... -
Page 6: Chapter 2 Installation
Power socket Connect the power cable to the switch PS3016S with an AC power supply of 100-240V to 50/60Hz Ground terminal Use a wire ground to prevent lightning strikes. To avoid lightning strikes on the product and extend the life of the product Chapter 2 Installation 2.1 Installation Precautions... - Page 7 seriously affecting the service life of equipment. The normal operation of this series of switches and storage temperature / humidity are as follows Environmental temperature Relative humidity description Working 0℃~40℃ 10%～90% RH no environment condensation Storage -40℃～70℃ 5%～90% RH no environment condensation ...
-
Page 8: Product Installation
2.2 Product installation 19-inch standard rack installation PS3016S is designed according to the standard 19-inch rack size, you can easily install to the rack, the specific installation steps are as follows: Check rack grounding and stability；... - Page 9 Do not connect the RJ45 port to the phone line SFP Port connection PS3016S SFP port only support Gigabit fiber module. Recommended use of standard SFP module products The process of installing a fiber module on a switch is as follows: First, grasp the optic fiber module from the side, insert it smoothly along the SFP port slot until the optic fiber module and switch are in close contact;...
- Page 10 Note： Does not allow excessive bending fiber, the radius of curvature should not be less than 10cm; Ensure the cleanliness of the fiber surface; Please do not look directly into the optical fiber connector with your eyes as this may cause eye injury 3.3 Check before power on Check whether the outlet power supply meets the switch specifications;...
- Page 11 Step 2、Manually changed the computer IP address to 192.168.254.X (X 为 2~254)，subnet mask is255.255.255.0 Step3、 Open computer's browser, type 192.168.254.1 in the address box, hit the Enter key Step4、Enter the default username and password “admin” and then click Login...
- Page 12 Step5、Entered the switch web management interface successfully when you see picture as below, you can begin to configure the switch...
-
Page 13: Chapter 4 Hardware Specifications
Chapter 4 Hardware Specifications Hardware Specifications IEEE 802.3i IEEE 802.3u IEEE 802.3x Standard IEEE 802.3ab IEEE 802.3af IEEE 802.3at 16 10/100Mbps RJ45 port 2 10/100/1000Mbps RJ45 port Port 2 Gigabit SFP port 1 Console port 16 10/100 Mbps RJ45 port support PoE+ power Total max power 150W Single max power 30W 18 Link/Act indicator... -
Page 14: Software Specifications
4.2Software Specifications IEEE 802.3:Ethernet Media Access Control (MAC) Protocol IEEE 802.3i:10BASE-T Ethernet IEEE 802.3u:100BASE-TX Fast Ethernet IEEE 802.3ab:1000BASE-T Gigabit Ethernet IEEE 802.3z:1000BASE-X Gigabit Ethernet (fiber) IEEE 802.3ad:Standard method for performing link Protocol aggregation standard IEEE 802.3x:flow control IEEE 802.1p:LAN Layer 2 Qos/Cos protocol for traffic priority (multicast filtering) IEEE 802.1q:VLAN IEEE 802.1d:STP Spanning tree... - Page 15 Support IP-MAC-PORT ternary binding Support ARP protection, IP source protection, DoS protection Support DHCP Snooping、DHCP attack protection Support 802.1X certificated、AAA Support port security, port isolation Support CPU protection Support POE power limit Support POE chip status view management Support setting PoE port priority Support setting PoE power supply time period Access control Support L2 (Layer 2) ~ L4 (Layer 4) packet filtering...
- Page 16 suppression Support broadcast suppression Support unknown unicast suppression Support static aggregation Link Support dynamic aggregation aggregation Support IP, MAC, and hybrid load balancing modes Supports up to 32 aggregation groups Support IPv6 Ping、IPv6 Tracert、IPv6 Telnet IPv6 Support IPv6 SSH 、IPv6 SSL Support WEB network management (HTTP, HTTPS, SSL V3) Support CLI (Telnet, SSH V1/V2, local serial port) Management...