Introduction; Purpose Of The Design Guide; Additional Resources - Danfoss VLT DriveMotor FCM 106 Design Manual

Introduction

1 1
1 Introduction

1.1 Purpose of the Design Guide

The Design Guide provides information required for
integration of the frequency converter in a diversity of
applications.
Literature available:
•
®
VLT
Instructions, for information required to install and
commission the frequency converter.
•
®
VLT
Guide,provides information required for
integration of the frequency converter into a
diversity of applications.
•
®
VLT
Programming Guide, for how to program the unit,
including complete parameter descriptions.
•
®
VLT
control panel (LCP).
•
®
VLT
operation pad (LOP).
•
Operating Instructions VLT
FCM 106 BACnet, and
Operating Instructions VLT
FCM 106 Metasys, for information required for
controlling, monitoring and programming the
frequency converter.
•
PC-based Configuration Tool MCT 10, enables the
user to configure the frequency converter from a
Windows™ based PC environment.
•
Danfoss VLT® Energy Box software, for energy
calculation in HVAC applications.
•
Approvals.
Technical literature and approvals are available online at
www.danfoss.com/BusinessAreas/DrivesSolutions/Documen-
tations/Technical+Documentation.
Danfoss VLT® Energy Box software is available at
www.danfoss.com/BusinessAreas/DrivesSolutions, PC software
download area.
This publication contains information proprietary to
Danfoss. By accepting and using this manual the user
agrees that the information contained herein is used solely
for operating equipment from Danfoss or equipment from
other vendors if such equipment is intended for communi-
cation with Danfoss equipment over a serial
communication link. This publication is protected under
the Copyright laws of Denmark and most other countries.
4
DriveMotor FCP 106 and FCM 106 Operating
DriveMotor FCP 106 and FCM 106 Design
DriveMotor FCP 106 and FCM 106
LCP Instruction, for operation of the local
LOP Instruction, for operation of the local
® DriveMotor FCP 106 and
®
DriveMotor FCP 106 and
®
VLT DriveMotor FCP 106 and FCM 106 Design Guide
Danfoss does not warrant that a software program
produced according to the guidelines provided in this
manual functions properly in every physical, hardware or
software environment.
Although Danfoss has tested and reviewed the documen-
tation within this manual, Danfoss makes no warranty or
representation, neither expressed nor implied, with respect
to this documentation, including its quality, performance,
or fitness for a particular purpose.
In no event shall Danfoss be liable for direct, indirect,
special, incidental, or consequential damages arising out of
the use, or the inability to use information contained in
this manual, even if advised of the possibility of such
damages. In particular, Danfoss is not responsible for any
costs, including but not limited to those incurred as a
result of lost profits or revenue, loss or damage of
equipment, loss of computer programs, loss of data, the
costs to substitute these, or any claims by third parties.
Danfoss reserves the right to revise this publication at any
time and to make changes to its contents without prior
notice or any obligation to notify former or present users
of such revisions or changes.

1.2 Additional Resources

Literature available:
•
•
•
•
•
•
MG03M102 - 08/2015
®
VLT DriveMotor FCP 106 and FCM 106 Operating
Instructions, for information required to install and
commission the frequency converter.
®
VLT DriveMotor FCP 106 and FCM 106 Design
Guide,provides information required for
integration of the frequency converter into a
diversity of applications.
®
VLT DriveMotor FCP 106 and FCM 106
Programming Guide, for how to program the unit,
including complete parameter descriptions.
®
VLT LCP Instruction, for operation of the local
control panel (LCP).
®
VLT LOP Instruction, for operation of the local
operation pad (LOP).
Operating Instructions VLT ® DriveMotor FCP 106 and
FCM 106 BACnet, and
®
Operating Instructions VLT DriveMotor FCP 106 and
FCM 106 Metasys, for information required for
controlling, monitoring and programming the
frequency converter.