Advantech ITA-5831 Series User Manual
  1. Manuals
  2. Brands
  3. Advantech Manuals
  4. Industrial PC
  5. ITA-5831 Series
  6. User manual
Advantech ITA-5831 Series User Manual

Advantech ITA-5831 Series User Manual

Intel the 6rd generation core i processor fanless system for railway applications
Hide thumbs Also See for ITA-5831 Series:
Table of Contents

Advertisement

Quick Links

Download this manual
User Manual
ITA-5831 Series
Intel® the 6rd Generation
Core™ i Processor Fanless
System for Railway Applications

Advertisement

Table of Contents
loading

Related Manuals for Advantech ITA-5831 Series

Summary of Contents for Advantech ITA-5831 Series

  • Page 1 User Manual ITA-5831 Series Intel® the 6rd Generation Core™ i Processor Fanless System for Railway Applications...
  • Page 2 No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. How- ever, Advantech Co., Ltd.
  • Page 3 Advantech has come to be known. Your satisfaction is our primary concern. Here is a guide to Advantech's cus- tomer services.
  • Page 4 Before setting up the system, check that the items listed below are included and in good condition. If any item does not accord with the table, please contact your dealer immediately.  1 x ITA-5831 series industrial computer  1 x ITA-5831 accessory box ...
  • Page 5 The sound pressure level at the operator's position according to IEC 704-1:1982 is no more than 70 dB (A). DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein.
  • Page 6 Warnings, Cautions and Notes Warning! Warnings indicate conditions, which if not observed, can cause personal injury! Caution! Cautions are included to help you avoid damaging hardware or losing data. e.g.There is a danger of a new battery exploding if it is incorrectly installed.

  • Page 7: Table Of Contents

    Contents Chapter Overview..........1 Introduction ....................2 Specifications .................... 2 Power Information ..................3 Table 1.1: Power input..............3 Environmental Specifications ..............3 Table 1.2: Environmental Specifications ........3 Dimension Diagram................... 4 Figure 1.1 Dimension Diagram of ITA-5831 ........ 4 Figure 1.2 Exploded Diagram of ITA-5831 ........5 Table 1.3: Parts list..............
  • Page 8 Figure 3.7 COM module (ITA-EM-SR61-001AE) ...... 20 3.1.4 Installing RTC ................21 Figure 3.8 Installing RTC............21 3.1.5 Installing Antennas ..............22 Figure 3.9 Installing antennas ........... 22 Chapter BIOS Setting ........23 Introduction ..................... 24 Entering Setup ..................24 Main Setup....................
  • Page 9 Appendix B Declaration of A the Presence Condition of the Restricted Substances Marking......75 Appendix C Safety Instructions Battery Information .........77 安全指示............78 電池信息............78 ITA-5831 User Manual...
  • Page 10 ITA-5831 User Manual...

  • Page 11: Chapter 1 Overview

    Chapter Overview Sections include:  Introduction  Specifications  Power Information  Environment Specifications  Dimension Diagram...

  • Page 12: Introduction

    Introduction The ITA-5831 is a fanless, compact embedded industrial computer chassis with the 6th Gen Core i processor and wide voltage input range, which is specially designed for intelligent transportation and road surveillance. This powerful computing platform can withstand operation 24 hours a day, 7 days a week. Specifications ...

  • Page 13: Power Information

    Power Information ITA-5831 power design complies with EN 50155 S2/C1. Table 1.1: Power input DC-IN Voltage 110V Voltage Range (0.7~1.25) 16.8 ~ 30V 33.6 ~ 60V 50.4 ~ 90V 77 ~ 137.5V Transient (0.6~1.4/0.1s) 14.4 ~ 33.6V 28.8 ~ 67.2V 43.2 ~ 100.8V 66 ~ 154V Power connector 1 x M12 S-coded (M) 4-pin...

  • Page 14: Dimension Diagram

    Dimension Diagram Figure 1.1 Dimension Diagram of ITA-5831 ITA-5831 User Manual...

  • Page 15: Figure 1.2 Exploded Diagram Of Ita-5831

    Figure 1.2 Exploded Diagram of ITA-5831 Table 1.3: Parts list Top cover Mounting kits Carrier board for easy-swap module Power module Real I/O panel Power module bracket Front panel (Internal) Front panel (Internal) Backplane Front panel Main board Heatsink Carrier board Easy-swap module (Optional) ITA-5831 User Manual...
  • Page 16 ITA-5831 User Manual...

  • Page 17: Chapter 2 H/W Installation

    Chapter H/W Installation Sections include:  Introduction  Jumpers and Connectors  I/O Connectors...

  • Page 18: Introduction

    Introduction The following sections show the internal jumpers setting and the external connectors pin assignment for application integration. Jumpers and Connectors 2.2.1 Jumper Description You may configure the ITA-5831 to match the needs of your application by setting jumpers. A jumper is a metal bridge used to close an electric circuit. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them.

  • Page 19: Jumper And Connector Location

    2.2.2 Jumper and Connector Location The main board has a number of connectors and jumpers that allow you to configure your system to suit your application. The table below lists the function of each of the connectors and jumpers. The locations of jumpers and connector on board are shown in Figure 2.1.

  • Page 20: Table 2.2: Bat1(Rtc Battery Pin Header)

    Table 2.2: BAT1(RTC battery pin header) Setting Power(3.3V) *Default setting Table 2.3: JCMOS1(Clear CMOS setting) Setting Default* Clear CMOS *Default setting Table 2.4: PMODE1(AT,ATX witch) Setting ATX * *Default setting ITA-5831 User Manual...

  • Page 21: I/O Connectors

    I/O Connectors Figure 2.2 ITA-5831 Front View Figure 2.3 ITA-5831 Real View ITA-5831 User Manual...

  • Page 22: Com Connector

    2.3.1 COM connector ITA-5831 provides two RS-232/422/485 DB9 connectors. The default setting is RS- 232. Table 2.5: COM Connector Pin Definition RS-232 RS-422 RS-485 Signal Name Signal Name Signal Name DATA- DATA+ 2.3.2 Audio connector Table 2.6: Audio Connector Pin Definition Signal Name Signal Name MICR...

  • Page 23: Digital I/O Connector

    2.3.3 Digital I/O connector ITA-5831 provides 1 x 8-bits DIO with DB9 type (4DI, 4 DO). Table 2.7: Digital I/O Connector Pin Definition Signal Name Signal Name GPI1 GPO1 GPI2 GPO2 GPI3 GPO3 GPI4 GPO4 2.3.4 USB connector ITA-5831 provides total 2 x USB3.0 with Type A connector and 1 x USB2.0 with M12 A-code female connector.

  • Page 24: Ethernet

    2.3.5 Ethernet ITA-5831 provides 3 x 10/100/1000M Ethernet with M12 x-coded. Table 2.10: Ethernet Connector Pin Definition Signal Name Signal Name MDI0+ MDI3+ MDI0- MDI3- MDI1+ MDI2- MDI1- MDI2+ 2.3.6 Power Input Table 2.11: Power Connector Pin Definition Signal Name Signal Name 2.3.7 LED Indicators for System Status...

  • Page 25: Chapter 3 System Setup

    Chapter System Setup Sections include:  Installing mini-PCIe card and mSATA on mainboard  Installing ITA-EM easy-swap modules  Installing RTC battery  Installing antennas...

  • Page 26: Introduction

    Introduction The following procedures instruct you how to install all modules into the ITA-5831 system. 3.1.1 Installing m-SATA ITA-5831 reserves 1 m-SATA slot on the mainboard and 3 mini-PCIe slot on the carrier board. Figure 3.1 Installing mini-PCIe and m-SATA Loosen the handscrews and pull out dual-SSD module from the front panel.

  • Page 27: Figure 3.2 Installing Mini-Pcie

    Figure 3.2 Installing mini-PCIe ITA-5831 User Manual...

  • Page 28: Installing Ssd

    3.1.2 Installing SSD ITA-5831 contains 1 x Dual-SSD module inside. To install the SSD, pull out the SSD bracket and lock it with 4 screws. Figure 3.3 Installing SSD (1) Loosen the hand screws and pull out the dual-SSD module on the front panel. Install the SSD on the bracket and lock the SSD with 4 screws on both sides.

  • Page 29: Installing Ita-Em Easy-Swap Modules

    3.1.3 Installing ITA-EM Easy-Swap modules ITA-5831 reserves a blank bracket for an easy-swap module to extend your extra I/O requirements. A dual-SSD module can be removed and changed for other easy- swap modules. Figure 3.5 Installing Easy-Swap modules (1) Loosen the handscrews and remove the blank bracket. Insert the ITA-EM module and lock the handscrews.

  • Page 30: Figure 3.6 Installing Easy-Swap Modules (2)

    Figure 3.6 Installing Easy-Swap modules (2) Figure 3.7 COM module (ITA-EM-SR61-001AE) ITA-5831 User Manual...

  • Page 31: Installing Rtc

    3.1.4 Installing RTC ITA-5831 RTC battery is mounted on the front panel. Open the RTC cover. Insert the RTC battery to the holder and plug in the cable. Lock the RTC cover. Figure 3.8 Installing RTC ITA-5831 User Manual...

  • Page 32: Installing Antennas

    3.1.5 Installing Antennas IT-5231 reserves antenna holes on the front panel. Loosen the handscrews and pull out the dual-SSD module from the front panel. Open the top cover. Loosen the screws to remove the dual-SSD bracket. Remove the carriage bracket for the easy-swap module. Insert the mini-PCIe, then lock it with 2 screws.

  • Page 33: Chapter 4 Bios Setting

    Chapter BIOS Setting...

  • Page 34: Introduction

    Introduction This chapter introduces how to configure BIOS for ITA-5831 series.With the AMI- BIOS Setup program, you can modify BIOS settings and control the special features of your computer. The Setup program uses a number of menus for making changes and turning the special features on or off.

  • Page 35: Main Setup

    Main Setup When you first enter the BIOS Setup Utility, you will enter the Main setup screen. You can always return to the Main setup screen by selecting the Main tab. There are two Main Setup options. They are described in this section. The Main BIOS Setup screen is shown below.

  • Page 36: Advanced Bios Setup

    4.3.1 Advanced BIOS Setup Select the Advanced tab from the ITA-5831 setup screen to enter the Advanced BIOS Setup screen. You can select any of the items in the left frame of the screen, such as CPU Configuration, to go to the sub menu for that item. You can display an Advanced BIOS Setup option by highlighting it using the <Arrow>...
  • Page 37 4.3.1.1 Trusted Computing  Security Device Support: Enable/Disable BIOS support for security device. The default setting is [Enable].  TPM state: Enable/disable security device. The default setting is [Enable]. Pending operation:  Schedule an operation for the security device. TPM can be clear or none. The default setting is [None]  ...
  • Page 38 4.3.1.2 PCH-FW Configuration This page shows the version, mode, type, SKU of ME firmware which build-in BIOS.   ITA-5831 User Manual...
  • Page 39 4.3.1.3 Embedded Controller Configuration This page shows a part of hardware information which accessed by EC. The user can get the temperature or voltage to analyze the status of system.  Mute: Control the system voice. The default settings is [Disable]. ...
  • Page 40 4.3.1.4 F81216 Controller Configuration The ITA-5831 support 2 serial ports. The user can configure the serial port in the sub- page. The serial port 60 is hardware reserved function, and the default setting is [dis- abled]. ITA-5831 User Manual...
  • Page 41 Serial Port 1/2 Configuration  Serial Port Enable /disable the serial port. The default setting is [Enabled].  Device Settings: Display the IO port and IRQ number which the port used.  Change settings[1]: Select an optimal settings for the serial port (IO port and IRQ). The default set- ting is [Auto].
  • Page 42 4.3.1.5 Serial Port Console Redirection This page shows the console status. The user can configure the console settings in [Console redirection Settings]. ITA-5831 User Manual...
  • Page 43  Console redirection: Enable/disable console redirection function. The default settings is [disabled].  Console Redirection Settings: When the function of console redirection is enabled, this BIOS sub-page can be entered. The settings specify how the host computer and the remote computer will exchange data.
  • Page 44 4.3.1.7 SATA Configuration  SATA Controller(s): Enable/disable SATA controllers. The default setting is [Enabled].  SATA Mode Selection Determines how SATA controllers operate, AHCI or RAID can be chosen. The default setting is [AHCI].  SATA Port 0/1/2/MSATA Enable/disable SATA ports. The default setting is [Enabled]. ...
  • Page 45 4.3.1.8 Network Stack Configuration  Network Stack Enable/Disable UEFI Network stack. The default setting is [Disabled].   ITA-5831 User Manual...
  • Page 46 When enable Network stack, the followed picture will be shown:  Ipv4 PXE Support: Enable/Disable IPV4 PXE support. If disabled, IPV4 PXE boot option will not be created.  Ipv6 PXE Support: Enable/Disable IPV6 PXE support. If disabled, IPV6 PXE boot option will not be created.
  • Page 47 4.3.1.9 CSM Configuration  CSM Support Enable/disable CSM support. The default setting is [Enabled].  GateA20 Active [Upon Request]: GA20 can be disabled using BIOS services. [Always]: Do not allow disabling GA20.  Option ROM Messages Set the display mode for option ROM. INT19 Trap Response ...
  • Page 48 4.3.1.10 USB Configuration  Legacy USB Support: Enable/disable legacy USB support. The default settings is [enabled].  XHCI Hand-off This is a workaround for OS without XHCI hand-off support. The XHCI owner- ship changes should be claimed by XHCI driver. ...
  • Page 49 4.3.1.11 PCIE COM Port Configuration ITA-5831 Support 4 PCIE slot serial ports. The user can configure serial port in sub page.  Serial Port 1/2/3/4 Mode: Select serial ports mode. [RS232],[RS422],[RS485] can be selected. The default setting is [RS232].   ITA-5831 User Manual...

  • Page 50: Chipset Configurations

    4.3.2 Chipset Configurations The user configures PCH and SA in the sub-page of chipset configurations. ITA-5831 User Manual...
  • Page 51 4.3.2.1 System Agent Configurations  VT-d Enable/disable VT-d function.  Above 4GB MMIO BIOS assignment Enable/disable above 4GB MMIO BIOS assignment. This is disabled by auto- matically when Aperture size is set to 2048MB.  Graphics Configuration Configure graphics settings. Please refer 4.5.1.1. ...
  • Page 52 Graphics Configuration  IGFX VBIOS Version Displays the current VBIOS version.  Graphics Turbo IMON Current Set the graphics turbo IMON current values supported(14-31).  GTT size Select the GTT size. Aperture size  Select the aperture size. If 2048MB aperture size is selected, please disable CSM support.
  • Page 53   Primary IGFX Boot Display  Select the video device which will be activated during POST. Secondary boot display selection will appear based on your selection. ITA-5831 supports HDMI,DVI, eDP panel and VGA. eDP LVDS Panel Type  Select ITB-172 LCD panel type. ...
  • Page 54 PEG Port Configuration  Enable Root Port Enable/disable the root port.  Max Link Speed Configure PEG port max link speed.  Detect Non-Compliance Device Detect non-compliance PCIE device in PEG port.   ITA-5831 User Manual...
  • Page 55 4.3.2.2 PCH-IO Configurations  Intel PCH RC Version Show the current Intel PCH RC version.  Intel PCH SKU Name Show the current Intel PCH SKU name. Intel PCH Rev ID  Show the current Intel PCH reversion id.  PCI Express Configuration Please refer 4.5.2.1 PCH LAN Controller...
  • Page 56 PCI Express Configuration This page shows the PCH supports the PCIE root ports. Detailed configurations below.   ITA-5831 User Manual...

  • Page 57: Security Configuration

     PCI Express Root Port Control the PCI Express root port.  Hot plug Enable/disable PCI Express hot plug.  PCIe speed Select PCI Express port speed. Detect Non-Compliance device  Detect non-compliance PCI Express device. If enable, it will take more time at POST time.

  • Page 58: Boot Configuration

    4.3.4 Boot Configuration Setup Prompt Timeout  Set the number of seconds to wait for setup activation key. The default setting is [1].  Bootup NumLock State Select the [NumLock] key in keyboard state. The default setting is [ON].  Quiet Boot Enable/disable quiet boot.

  • Page 59: Save & Exit Configuration

    4.3.5 Save & Exit Configuration Save Changes and Exit  Exit system setup after saving the changes.  Discard Changes and Exit Exit system setup without saving any changes. Save Changes and Reset  Reset the system after saving the changes. ...
  • Page 60 ITA-5831 User Manual...

  • Page 61: Chapter 5 Driver Installation

    Chapter Driver Installation Sections include:  Chipset Windows Driver Setup  VGAWindows Driver Setup  ME Windows Driver Setup  LAN Windows Driver Setup  USB 3.0 Windows Driver Setup...

  • Page 62: Introduction

    Introduction Advantech offers a complete range of device driver and software supports for Win- dows programming developers. You can apply the Windows Device Drivers to the most popular Windows Programming tools, such as Visual C++, Visual Basic, Bor- land C++ Builder and Borland Delphi. Here Windows 7 is taken as an example.

  • Page 63: Chipset Windows Driver Setup

    5.2.1 Chipset Windows Driver Setup Insert the driver CD into your system’s CD-ROM driver. You can see the driver folder items. Navigate to the "INF" folder and click "Setup" to complete the installation. ITA-5831 User Manual...
  • Page 64 ITA-5831 User Manual...
  • Page 65 ITA-5831 User Manual...

  • Page 66: Vga Windows Driver Setup

    5.2.2 VGA Windows Driver Setup Insert the driver CD into your system’s CD-ROM drive. You can see the driver folders items. Navigate to the "VGA" folder and click "Setup" to complete the installation of the drivers. 5.2.3 ME Windows Driver Setup Insert the driver CD into your system’s CD-ROM drive.

  • Page 67: Lan Windows Driver Setup

    5.2.4 LAN Windows Driver Setup Insert the driver CD into your system’s CD-ROM drive. You can see the driver folders items. Navigate to the "LAN" folder and click "Setup" to complete the installation of the drivers. 5.2.5 US3.0 Windows Driver Setup Insert the driver CD into your system’s CD-ROM driver.
  • Page 68 ITA-5831 User Manual...

  • Page 69: Chapter 6 Gpio Programming Guide

    Chapter GPIO Programming Guide This chapter introduces GPIO programming Guide.

  • Page 70: Ita-5831 Digital Dio Definition

    Note! Please download the NXP Semiconductors PAC9554 spec for program- ming from NXP’s website. https://www.nxp.com/docs/en/data-sheet/ PCA9554_9554A.pdf?fsrch=1&sr=1&pageNum=1 ITA-5831 Digital DIO Definition See Section 2.3.3. Configuration Sequence ITA-5831’s GPIO is realized through PCA9554 GPIO IC connected to ICH SMBUS. Therefore, the configuration and access to GPIO IC is completed by IO Space accessing to ICH SMBUS controller.

  • Page 71: Command Byte

    Table 6.2: Pin Define n.c. 3,8,13,18 Not connected 6.2.1 Command byte Table 6.3: Command Byte Command Protocol Function Read byte Input Port register Read/Write byte Output Port register Read/Write byte Polarity inversion register Read/Write byte Configuration register The command byte is the first byte to follow the address bute during a write transmission.

  • Page 72: Pca9554 Register 1 - Output Port Register

    6.2.3 PCA9554 Register 1 – Output Port register This register reflects the outgoing logic levels of the pins defined as outputs by Regis- ters 3. Bit values in this register have no effect on pins defined as inputs. Reads from this register return the value that is in the fili-flop controlling the output selection, not the actual pin value.

  • Page 73: Pca9554 Register 3 - Configuration Register

    6.2.5 PCA9554 Register 3 – Configuration register The register configures the directions of the I/O pins. If a bit this register is set, the corresponding port pin is enabled as an input with high-impedance output driver. If a bit in this register is cleared, the corresponding port pin is enabled as an output. At reset, the I/Os are configured as inputs with weak pull-up to VDD.
  • Page 74 Function call for reference: ............................ICH SMBUS Access Code (The following code is realized by simulating the access of BIOS to SMBUS. It uses Borand C++. 3.1 for compiling and is successfully tested under DOS (But it is not tested under other OSs). #define SMBUS_PORT 0xF040 //SMB_BASE is 0xF040 typedefunsigned char BYTE;...
  • Page 75 chk_smbus_ready(); //wheater SMBUS is ready return (inportb(SMBUS_PORT + 5)); // Byte value read from SMB_BASE + 5 ///////////////////////////////////////////////////////////////////// void smbus_write_byte(BYTE addr, BYTE offset, BYTE value) // Write SMBUS Register byte value. Write one byte value each time. addr is slave address (such as 0x40), and offset is register offset int i;...
  • Page 76 ///////////////////////////////////////////////////////////////////// chk_smbus_ready() // To decide whether SMBUS is ready or has completed the action, you should wait for a long time to check whether SMBUS has successfully transmitted the command. Since error may rarely occurs, BIOS code does not make judgement on the return value of this function in read and write of SUMBUS byte.
  • Page 77 ///////////////////////////////////////////////////////////////////// BYTE check_data (W ORD addr) int i; BYTE data; for(i = 0; i <= 6; i++) data = inportb(addr); if (data!= 0) break; return data; ///////////////////////////////////////////////////////////////////// void newiodelay() //Shorter delay outportb(0xeb, 0); // IO port 0xeb No real device occupies. Write a value to this port can realize delay function.
  • Page 78 ********************************************************************* GPIO Simcodes (take GPIO 00 and GPIO 07 as an example) Output High to GPIO 00: data = smbus_read_byte(0x40, 0x03); //Read slave 0x40 register 3 byte data &= 0xfe;//Set bit 0 as 0 smbus_write_byte(0x40, 0x03, data)//write, set GPIO 00 as Output data = smbus_read_byte(0x40, 0x01) //Read slave 0x40 register 1 data |= 0x01;...

  • Page 79: Appendix A A Programming The Watchdog Timer

    Appendix A Programming the Watchdog Timer...

  • Page 80: Programming The Watchdog Timer

    Programming the Watchdog Timer The ITA-5831's watchdog timer can be used to monitor system software operation and take corrective action if the software fails to function within the programmed period. This section describes the operation of the watchdog timer and how to pro- gram it.
  • Page 81 Data Port: Port 0x299 Action Description Send Write data to EC Get Read data from EC Note! After you write data/command to 299/29A port, IBF will be set 1. You must wait IBF clear to zero, then you can write next data/com- mand to 299/29A port.
  • Page 82 Example Program //Wait IBF Empty unsigned char ECWaitIBFEmpty() unsigned char Status; Status = inportb(0x29A); //Read back Status } while (Status & 0x02); //If IBF Set? return Status; //Write non-data command (no data) to EC void EcWriteCmd (unsigned char cmd) ECWaitIBFEmpty();//Wait IBF Empty outpor tb(0x29A, (unsigned char)cmd);...
  • Page 83 //Start watchdog void enable_wdt( i nt time, //Time int timebase //Time base: 0: second 1: minute unsigned int time_word; EcWriteCmd(0x29); //Write command 0x29 to stop watch dog if (timebase == 0) //Second base = 100ms * 10 time_word = time * 10; else //Minute base = 100ms * 600 time_word = time * 600;...
  • Page 84 ITA-5831 User Manual...

  • Page 85: Declaration Of A The Presence Condition Of The Restricted Substances Marking

    Appendix Declaration of A the Presence Condition of the Restricted Substances Marking...
  • Page 86 BSMI RoHS 限用物質含有情況標示確認表 Declaration of the Presence Condition of the Restricted Substances Marking 設備名稱：電腦 型號 （型式） ：ITA-5831 Equipment name Type designation (Type) 限用物質及其化學符號 Restricted substances and its chemical symbols 單元 六價鉻 多溴聯苯 多溴二苯醚 鉛 汞 鎘 Unit Hexavalent Polybrominated Polybrominated Lead Mercury Cadmium...

  • Page 87: Safety Instructions Battery Information

    Appendix Safety Instructions Battery Information...

  • Page 88: 安全指示

    安全指示 請仔細閱讀此安全操作說明。 請妥善保存此用戶手冊供日後參考。 用濕抹布清洗設備前，請從插座拔下電源線。請不要使用液體或去汙噴霧劑清洗 設備。 對於使用電源線的設備，設備周圍必須有容易接觸到的電源插座。 請不要在潮濕環境中使用設備。 請在安裝前確保設備放置在可靠的平面上，意外跌落可能會導致設備損壞。 設備外殼的開口是用於空氣對流，從而防止設備過熱。請不要覆蓋這些開口。 當您連接設備到電源插座上前，請確認電源插座的電壓是否符合要求。 請將電源線佈置在人們不易絆到的位置，並不要在電源線上覆蓋任何雜物。 請注意設備上的所有警告標識。 如果長時間不使用設備，請將其同電源插座斷開，避免設備被超標的電壓波動損 壞。 請不要讓任何液體流入通風口，以免引起火災或者短路。 請不要自行打開設備。為了確保您的安全，請由經過認證的工程師來打開設備。 如遇下列情況，請由專業人員來維修： 電源線或者插頭損壞； 設備內部有液體流入； 設備曾暴露在過於潮濕的環境中使用； 設備無法正常工作，或您無法通過用戶手冊來使其正常工作； 設備跌落或者損壞； 設備有明顯的外觀破損。 請不要把設備放置在超出我們建議的溫度範圍的環境，即不要低於 -25°C （-13°F）或高於 60°C （140°F） ，否則可能會損壞設備。 此為 A 級產品，在生活環境中，該產品可能會造成無線電干擾。在這種情況下， 可能需要使用者對干擾採取切實可行的措施。 本產品不帶電線元件銷售，應購買已通過 CCC 認證的電線元件。 注意：電腦配置了由電池供電的即時時鐘電路，如果電池放置不正確，將有爆炸的危 險。因此，只可以使用製造商推薦的同一種或者同等型號的電池進行替換。請按照製 造商的指示處理舊電池。 根據 IEC 704-1:1982 的規定，操作員所在位置的聲壓級不可高於 70dB(A)。 免責聲明：該安全指示符合...
  • Page 89 ITA-5831 User Manual...
  • Page 90 No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permis- sion of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2018...

Table of Contents