NTN-SNR LINEAR AXIS AXC Series Manual page 240

G
Gantry Axis __________37, 50, 134 - 141, 149 - 154, 217 - 219
Gantry Axis with lateral toothed belt drive _____149 - 151
Gantry Axis with rack and pinion drive
________________________ 37, 50, 134 - 141, 149 - 154
Gantry Axis with toothed belt drive
________________________ 37, 50, 134 - 141, 217 - 219
Gantry connection ______________________________ 173, 174
Gantry support legs_____________________________206 - 208
Gearbox selection ____________________________________ 20
Maximum acceleration torque _____________________ 20
Maximum operation speed ________________________ 20
Nominal torque on the drive _______________________ 20
Gearbox ______________________________ 27 - 29, 181 - 186
Integrated planetary gearbox ________________181 - 185
Mounted gearboxes _______________________181 - 186
Grease nipple __________________________ 8, 34, 36, 39, 212
Groove inserts ______________________________________ 208
Aluminum groove insert _________________________ 208
Plastic groove insert ____________________________ 208
Guide to queries _______________________________234 - 236
Guiding systems __________________________________12, 13
Linear guide ____________________________________ 12
Track roller guide ________________________________ 13
H
Hammer nut ____________________________________ 25, 168
Hammer screw _________________________________ 25, 168
I
Influence factors __________________________________17, 40
Intended use ________________________________________ 16
L
Life time ____________________________________________ 17
Nominal life time _________________________________ 17
Lifting Axis ___________________ 37, 50, 134 - 141, 217 - 219
Line splitter _________________________________________ 202
Linear guide ____________________ 7, 12, 17, 32 - 41, 46 - 50
Linear motor ____________________ 7, 9, 11, 37, 72, 155 - 163
Linear motor with air cooling ____________ 72, 155 - 163
Linearmotor with water cooling __________ 72, 155 - 163
Linear motor drive __________________________________9, 11
Linear table _____________ 16, 29, 30, 48, 103 - 112, 170, 172
Linear table with ball screw drive _________ 48, 103 - 112
Linear table with trapezodial screw drive __ 48, 103 - 112
Line splitter _________________________________________ 202
Load capacity _______________________________________ 17
Dynamic load capacity ___________________________ 17
Static load capacity ______________________________ 17
Lubrication ______________________________________ 32 - 42
Lubricants __________________________________ 32 - 34
Lubrication amount __________________________ 38 - 40
Lubrication intervals ___________________________41, 42
Lubrication methods __________________________34, 35
Lubrication points ____________________________36, 37
M
_________________________________________________
Main parameters _________________________________ 51 - 53
Maintenance and lubrication _______________________ 32 - 45
Brush wiper replacement _________________________ 43
Cover strip replacement ______________________ 43 - 45
Lubricants __________________________________ 32 - 34
Lubrication amount __________________________ 38 - 40
Lubrication intervals ___________________________41, 42
Lubrication methods __________________________34, 35
Lubrication points ____________________________36, 37
Wear part set ___________________________________ 45
Measuring device for the toothed belt tension ___________9, 30
Mounting _______________________________________ 22 - 25
Design of the mounting surfaces ________________22, 23
Monting instruction ___________________________24, 25
Mounting tolerances __________________________22, 23
Multi Axis systems ______________________________213 - 219
Standard combinations _____________________217 - 219
N
Nominal life time _____________________________________ 17
O
Operating temperature ________________________________ 16
Options ___________________ 178 - 193, 195 - 199, 224 - 227
Configuration versions ______________________224 - 226
Safety options _________________________________ 227
P
Parallele Axis _______________________________ 47, 86 - 102
Parallele Axis with ball screw drive _________ 47, 91 - 98
Parallele Axis with toothed belt drive ________ 47, 86 - 90
Parallele Axis with toothed belt / Ω - drive. __ 47, 99 - 102
Parallele Axis with trapezodial screw ________ 47, 91 - 98
Planetary gearbox __________________________ 27, 181 - 186
Plug-in shaft ________________________________________ 178
Position accuracy _________________________ 10, 11, 15, 130
Positioning repeatability _________ 10, 11, 15, 48, 49, 55 - 153
Precision ____________________________________________ 19
Precision Axis ______________________________ 48, 113 - 130
Precision Axis with ball screw drive _______ 48, 113 - 130
Precision classes ________________________________ 48, 130
Push-in fittings ______________________________________ 212
238