NTN-SNR LINEAR AXIS AXC Series Manual page 189

A universal version is an adaptation via integrated coupling in combination with a coupling cone. Here, the coupling half on the axis
side is screwed to the drive pulley and offers by the force-fitted torque transmission even under high dynamic optimal reliability.
For usual market drives with a standard B5 flange is a wide range of coupling cones available. Clamping hubs with groove are used
as standard for driving shafts with feather key. Also available as a special design are clamping ring hubs for smooth shafts. In Table
6.23 the code numbers and dimensions for each Linear Axis are summarized and in the dimensions are shown in Figure 6.34.
Table 6.23 __ Code numbers and dimensions for force-fitted drive adaptions via coupling and couplig cone
Code
Type Design type
number
AXC40ZG
A B5 TK63
AXC40AG
A LP070
AXC60ZG
E B5 C120
AXC60AG
I B14 C60
A B5 C160
B B5 C120
C B5 C120
AXC80ZG
AXC80AG
D LP070
E LP090
F B14 C80
B5 C120
A
B14 C120
AXC100ZG
B B5 C160
C LP090
A B5/B14 C120
AXC100ZG_-D
B B5 C160
AXF100ZG
C LP090
A B5 C120
AXC120ZG
AXC120AG B B5 C160
AXDL240AG
C B5 C200
A B5 C120
C LP070
AXDL110Z
E CP060
F B14 C80
A B5 C120
B LP070
AXDL160Z C LP090
D B14 C80
E B5 C160
A B5 C120
AXDL160A
C LP090
A B5 C120
AXDL240Z B B5 C120
E B5 C160
A P
AXS280Z B B5 C160
C LP120
1 - Graphic account of the dimension in Chapter 3.6.1 Figure 3.10
2 - Clamping hub / Tension ring hub
3 - Stud bolt
X: Code number for special adapters
Figure 6.33 __ Dimensions drive adaptions
e2 a s1 b2
[mm] [°] [mm]
63 45 4 x M4 x 8 40
62 0 4 x Ø 5,5 52
100 45 4 x M6 x 12 80
52 45 4 x Ø 5,5 40
130 45 4 x M8 x 16 110
100 45 4 x M6 x 12 80
100 45 4 x M6 x 15 80
62 0 4 x Ø 5,5 52
80 0 4 x Ø 6,5 68
70 45 4 x Ø 6,5 60
100 45 4 x M6 x 15 80
100 45 4 x Ø 10,5 x 14 80
130 45 4 x M8 x 20 110
80 0 4 x Ø 6,6 68
100 45 4 x Ø 10,5 x 10 80
130 45 4 x M8 x 15 110
80 0 4 x Ø 6,6 68
100 45 4 x M6 x 18 80
130 45 4 x M6 x 18 110
165 45 4 x M10 x 20 130
100 45 4 x M6 x 10 80
62 0 4 x Ø 5,5 52
52 45 4 x Ø 5,5 40
70 45 4 x Ø 6,6 60
100 45 4 x M6 x 15 80
62 0 4 x Ø 5,5 52
80 0 4 x Ø 6,6 68
70 45 4 x Ø 6,6 60
130 45 4 x M8 x 18 110
100 45 4 x M6 x 10 80
80 0 4 x Ø 6,6 68
100 45 4 x M6 x 29 80
100 45 4 x M6 ³ 80
130 45 4 x M8 x 18 110
120 45 4 x M8 x 15 90
130 45 4 x M8 x 10 110
108 0 4 x Ø 9 x 16 90
d d i2 i2 -l
min. max. max. max.
[mm] [mm] [mm] [mm]
6 10 23,0 7,0
16 16 36,0 8,0
19 20 40,0 15,0
14 14 38,0 6,5
19 25 52,0 15,0
19 25 50,0 12,0
14 20 41,0 4,0
16 16 36,0 8,0
22 25 52,0 22,0
19 20 40,0 11,0
19 20 47,0 4,0
24 25 58,0 15,0
19 30 60,0 17,0
22 22 67,0 24,0
19 25 58,0 15,0
19 30 60,0 17,0
20 25 53,0 10,0
19 25 50,0 7,0
24 30 60,0 18,0
25 35 61,0 26,0
14 20 47,5 10,0
14 20 45,5 8,0
14 20 45,5 8,0
20 25 59,5 22,0
14 20 43,0 0,0
14 25 51,5 8,5
14 25 54,0 11,0
14 20 49,0 6,0
19 30 60,0 17,0
14 25 50,0 7,5
20 25 54,0 11,0
14 20 43,0 1,0
25 25 53,0 11,0
25 30 62,0 20,0
32 32 88 52
25 30 62 14
32 32 77 24
187
k2 a2 L2 LK 1
[mm] [mm] [mm] [mm]
31,0 /
54,0 72 37,0
38,0 2
70 80 58,0
96 120 65,0 50,0
64 80 56,5
120 150 74,0
90 110 71,0
83 110 62,0
59,0
82 100 66,0
80 90 81,0
80 110 70,0
100 112 65,0
100 116 76,0
61,0
115 145 78,0
100 130 85,0
90 116 76,0
120 160 78,0 59,0
100 135 71,0
120 150 72,0
-- 160 83,0 65,0
-- 200 91,0
82 110 42,5
80 110 40,5
32,5
80 110 40,5
82 110 54,5
86 120 22,5
78 106 31,0
100 135 33,5 22,5
86 120 28,5
120 150 39,5
100 115 74,5
67,0
100 130 78,0
96 120 11,0
96 120 21,0 10,0
115 150 30,0
48 -4
10 1
25 -4