Henny Penny Evolution Elite EEG-16 Series Technical Manual page 33

S S P P - - 3 3 0 0 Skip 'SKIM' Prompt? - YES or NO
S S P P - - 3 3 1 1 Skip 'EXP FLTR CONFIRM' Prompt? - YES or NO
S S P P - - 3 3 2 2 2-Stage Wash Enabled? - YES or NO
S S P P - - 3 3 3 3 Daily Filter Lockout Enabled? - YES or NO
S S P P - - 3 3 4 4 Daily Filter Period Start Time (i.e.: 5:00)
S S P P - - 3 3 5 5 Daily Filter Reminder Time (i.e.: 21:00)
S S P P - - 3 3 6 6 SKIP....
5 5 . . 1 1 . . 1 1 S S P P - - 1 1 T T e e m m p p e e r r a a t t u u r r e e
The left display flashes "SP-1" and "TEMP", "FORMAT".
1 1 ) )
Press the up or down arrow button to choose °F or °C.
2 2 ) )
5 5 . . 1 1 . . 2 2 S S P P - - 2 2 L L a a n n g g u u a a g g e e
Press and release the right arrow until "SP-2" "LANGUAGE" flashes on the left
1 1 ) )
display.
Press the up or down arrow to select desired language.
2 2 ) )
5 5 . . 1 1 . . 3 3 S S P P - - 3 3 S S y y s s t t e e m m I I n n i i t t i i a a l l i i z z a a t t i i o o n n
Press and release the right arrow until "SP-3" "DO SYSTEM INIT" flashes in the
1 1 ) )
display, along with "INIT" on the right display.
To reset the controls to factory default settings, press and hold the ✓ button and
2 2 ) )
controls count down "IN 3", "IN 2", "IN 1". Once the display shows "-INIT-" and
"*DONE*", the controls are reset to factory defaults.
5 5 . . 1 1 . . 4 4 S S P P - - 4 4 A A u u d d i i o o V V o o l l u u m m e e
Press and release the right arrow until "SP-4" "VOLUME" flashes in the left
1 1 ) )
display.
Press the up or down arrow, or product buttons, to adjust the speaker volume,
2 2 ) )
10 being loudest and 1 being the most quiet.
5 5 . . 1 1 . . 5 5 S S P P - - 5 5 A A u u d d i i o o T T o o n n e e
Press and release the right arrow until "SP-5" "TONE" flashes in the left display.
1 1 ) )
Press the up or down arrow button, or product buttons, to adjust the tone of the
2 2 ) )
speaker, 2000 being the maximum value and 50 being the minimum.
5 5 . . 1 1 . . 6 6 S S P P - - 6 6 M M e e l l t t C C y y c c l l e e S S e e l l e e c c t t i i o o n n
Press and release the right arrow until "SP-6 MELT CYCLE SELECT" scrolls in
1 1 ) )
the left display. Unless solid oil is being used in the vats, the right display should
show "1.LIQUID".
If solid shortening is used, the unit must be equipped to handle solid oil.
2 2 ) )
Use the up or down arrow to change the right display to "2.SOLID".
3 3 ) )
5 5 . . 1 1 . . 7 7 S S P P - - 7 7 I I d d l l e e M M o o d d e e E E n n a a b b l l e e d d
An Idle Mode allows the oil temperature to drop to a lower temperature when not in
use. This saves on oil and utilities.
21