Various Setting Values - Mitsubishi LE-40MTB-E Instruction Manual

11.3 Various settng values
The items indicated with white letters on a black ground must be always set. Another items are set in ac-
cordance with the functinon used.
Set items
Tension set value (N)
Tension
setting Tension set value(×10N)
Full scale value
Full scale
Decimal point (N)
tension
Decimal point (×10N)
Zero adjustment
Tension
detector Span adjustment
target value
Display time constant
Filter
TMO output time constant
Zero tension
Zero tension (N)
detection
value Zero tension (×10N)
Manual setting Manual set value
Taper ratio(int. diameter)
Linear
taper Taper ratio(ext. diameter)
Corner 1~4
Non-linear
taper
Taper 1~4
Stall Stall set value
Timer Start timer
Gain 1
Output gain
Gain 2
New reel preset value
New reel
/old reel Preset timer
switch-over
Old reel cut torque
Stop timer
Stop control Stop gain
Stop bias
Reel
A
Mechanical loss
correction
Reel
B
Minimum diameter
Reel diameter
Maximum diameter
Proportional gain (P gain)
Integral time
Manual
setting
Dead zone gain
Dead zone width
Automatic
Addition torque
gain setting
Password
When LE-40MD reel diameter calculation unit is connected, refer to the instruction manual of the LE-40MD.
*1 : Classification in memory column
Menu refers to the data saved in the menu table memory.
System refers to the data saved as common data in the system memory.
*1 : Symbol in memory column
: Data set on the operator screen.
: Data set on the engineer screen displayed after the password is entered.
: Data set on the engineer screen displayed after the password is entered or displayed for initial setting.
*2 : The initial adjustment constants are saved in the system memory.
*3 : The setting of the item marked with "
the MC1 input is turned on.
Set values Unit
N
N
–
–
–
–
N
×10N
s
s
N
×10N
%
%
%
mmφ
%
%
s
%
%
%
s
%
s
%
%
Powder mode %
AC servo mode %
Powder mode %
AC servo mode %
mmφ
mmφ
%
%
%
%
%
–
× " on the " Setting during operation "column cannnot be changed while
Set range
Minimum Maximum
0.1 ,1 or 10 ~ FS tension
0.01 ,0.1 or 1 ~ FS tension
1 1999
0.1, 1.0 or 10
0.01 ,0.1 or 1
0 0
1 digit ~ FS tension
(1/3 or more of FS tension)
1/4, 1/2, 1, 2,or 4
0 1999
0 199.9
0 100
0 80
0 100
0 2000
0 100
0 100
0.0 10.0
5 400
5 400
0 100
0.0 30.0
0 100
0.0 100.0
5 400
0 50
0 100
–50 100
0 100
–50 100
0 2000
Minimum set
2000
diameter
0 100
1 100
0 100–P gain
0 100
0 100
0 32767
71
Memory *1
Initial
Setting
during
value
Menu Syst.
operation
–
–
×
500
×1 ×
×0.1 ×
×
0
*2
500
×
*2
50.0
1/2
1/2
×
0
×
0.0
–
0
0
0
0
20
4.0
100
100
50
4.0
10
6.0
100
0
0
0
0
0
×
100
×
1000
50
50
0
50
20
4095
*3
Mainly
refer
page
18
18
12
12
12
12
12
35
42
36
36
18
31
32
33
33
15
28
29
29
25
25
38
28
28
28
37
37
37
37
32
32
35
35
35
35
34
10