Hitachi SJ700D-3 SERIES Quick Reference Manual page 73

Code Function name
P001 Operation mode on expansion card 1 error
P002 Operation mode on expansion card 2 error
P011 Encoder pulse-per-revolution (PPR) setting
P012 Control pulse setting
P013 Pulse input mode setting
P014 Home search stop position setting
P015 Home search speed setting
P016 Home search direction setting
P017 Home search completion range setting
P018 Home search completion delay time setting
P019 Electronic gear set position selection
P020 Electronic gear ratio numerator setting
P021 Electronic gear ratio denominator setting
P022 Feed-forward gain setting
P023 Position loop gain setting
P024 Position bias setting
P025 Temperature compensation thermistor enable
P026 Over-speed error detection level setting
P027 Speed deviation error detection level setting
P028 Numerator of motor gear ratio
P029 Denominator of motor gear ratio
P031 Accel/decel time input selection
P032 Positioning command input selection
P033 Torque command input selection
P034 Torque command setting
Polarity selection at the torque command
P035
input via O2 terminal
P036 Torque bias mode
P037 Torque bias value
P038 Torque bias polarity selection
Speed limit for torque-controlled operation
P039
(forward rotation)
Speed limit for torque-controlled operation
P040
(reverse rotation)
P044 DeviceNet comm watchdog timer
P045 Inverter action on DeviceNet comm error
DeviceNet polled I/O: Output instance
P046
number
P047 DeviceNet polled I/O: Input instance number
P048 Inverter action on DeviceNet idle mode
P049 DeviceNet motor poles setting for RPM
(Note) < >indicate the setting range of 75 to 150kW
Chapter 4
Monitored data or setting
00 (tripping), 01 (continuing operation)
128. to 9999., 1000 to 6500 (10000 to 65000) (pulses)
00 (ASR), 01 (APR), 02 (APR2), 03 (HAPR)
00 (mode 0), 01 (mode 1), 02 (mode 2)
0. to 4095.
"start frequency" to "maximum frequency"
(up to 120.0) (Hz)
00 (forward), 01 (reverse)
0. to 9999., 1000 (10000) (pulses)
0.00 to 9.99 (s)
00 (feedback side), 01 (commanding side)
1. to 9999.
1. to 9999.
0.00 to 99.99, 100.0 to 655.3
0.00 to 99.99, 100.0
-204 (-2048.) / -999. to 2048
00 (no compensation), 01 (compensation)
0.0 to 150.0 (%)
0.00 to 99.99, 100.0 to120.0 (Hz)
1. to 9999.
1. to 9999.
00 (digital operator), 01 (option 1), 02 (option 2),
03 (easy sequence)
00 (digital operator), 01 (option 1), 02 (option 2)
00 (O terminal), 01 (OI terminal), 02 (O2 terminal),
03 (digital operator)
0. to 200. (%) <0. to 180. (%)>
00 (as indicated by the sign),
01 (depending on the operation direction)
00 (disabling the mode), 01 (digital operator),
02 (input via O2 terminal)
-200. to +200. (%) <-180. to +180. (%)>
00 (as indicated by the sign),
01 (depending on the operation direction)
0.00 to "maximum frequency" (Hz)
0.00 to 99.99 (s)
00 (tripping),
01 (tripping after decelerating and stopping the motor),
02 (ignoring errors),
03 (stopping the motor after free-running),
04 (decelerating and stopping the motor)
20, 21, 100
70, 71, 101
00 (tripping),
01 (tripping after decelerating and stopping the motor),
02 (ignoring errors),
03 (stopping the motor after free-running),
04 (decelerating and stopping the motor)
0, 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26,
28, 30, 32, 34, 36, 38 (poles)
4 - 15
List of Data Settings
Change during
Default
RUN operation
FF FEF FUF b031≠10 b031=10
00 Not Allowed
00 Not Allowed
1024. Not
00 Not
00 Not
0. Not Allowed
5.00 Not Allowed
00 Not Allowed
5. Not Allowed
0.00 Not Allowed
00 Not Allowed
1. Allowed Allowed
1. Allowed Allowed
0.00 Allowed Allowed
0.50 Allowed Allowed
0. Allowed Allowed
00 Not Allowed
135.0 Not Allowed
7.50 Not Allowed
1. Not Allowed
1. Not Allowed
00 Not
00 Not Allowed
00 Not
0. Allowed Allowed
00 Not
00 Not
0. Allowed Allowed
00 Not
0.00
Allowed Allowed
0.00 Allowed Allowed
1.00 Not
01
Not
21
Not
71 Not
01
Not
0
Not
Not
Not
Not
Not
Not
Not
Not
Not
Not
Not
Not
Not
Not
Not