Hitachi SJ700D-3 SERIES Quick Reference Manual page 69

Code Function name
C021 Terminal [11] function
C022 Terminal [12] function
C023 Terminal [13] function
C024 Terminal [14] function
C025 Terminal [15] function
C026 Alarm relay terminal function
C027 [FM] signal selection
C028 [AM] signal selection
C029 [AMI] signal selection
Digital current monitor reference
C030
value
C031 Terminal [11] active state
C032 Terminal [12] active state
C033 Terminal [13] active state
C034 Terminal [14] active state
C035 Terminal [15] active state
C036 Alarm relay active state
Monitored data or setting
00 (RUN: running), 01 (FA1: constant-speed reached),
02 (FA2: set frequency overreached),
03 (OL: overload notice advance signal (1)),
04 (OD: output deviation for PID control),
05 (AL: alarm signal),
06 (FA3: set frequency reached), 07 (OTQ: over-torque),
08 (IP: instantaneous power failure),
09 (UV: under voltage), 10 (TRQ: torque limited),
11 (RNT: operation time over), 12 (ONT: plug-in time over),
13 (THM: thermal alarm signal), 19(BRK:brakge release),
20(BER:braking error)21 (ZS: 0 Hz detection signal),
22(DSE:speed deviation maximum),
23(POK:positioning completed),
24 (FA4: set frequency overreached 2),
25 (FA5: set frequency reached 2),
26 (OL2: overload notice advance signal (2)),
27 (Odc: Analog O disconnection detection),
28 (OIDc: Analog OI disconnection detection),
29 (O2Dc: Analog O2 disconnection detection),
31 (FBV: PID feedback comparison),
32 (NDc: communication line disconnection),
33 (LOG1: logical operation result 1),
34 (LOG2: logical operation result 2),
35 (LOG3: logical operation result 3),
36 (LOG4: logical operation result 4),
37 (LOG5: logical operation result 5),
38 (LOG6: logical operation result 6),
39 (WAC: capacitor life warning),
40 (WAF: cooling-fan speed drop),
41 (FR: starting contact signal),
42 (OHF: heat sink overheat warning),
43 (LOC: low-current indication signal),
44 (M01: general-purpose output 1),
45 (M02: general-purpose output 2),
46 (M03: general-purpose output 3),
47 (M04: general-purpose output 4),
48 (M05: general-purpose output 5),
49 (M06: general-purpose output 6),
50 (IRDY: inverter ready), 51 (FWR: forward rotation),
52 (RVR: reverse rotation), 53 (MJA: major failure),
54(WCO: window comparator O),
55(WCOI: window comparator OI),
56 (WCO2: window comparator O2)
(When alarm code output is selected for "C062", functions "AC0" to
"AC2" or "AC0" to "AC3" [ACn: alarm code output] are forcibly
assigned to intelligent output terminals 11 to 13 or 11 to 14,
respectively.)
00 (output frequency), 01 (output current),
02 (output torque), 03 (digital output frequency),
04 (output voltage), 05 (input power),
06 (electronic thermal overload), 07 (LAD frequency),
08 (digital current monitoring), 09 (motor temperature),
10 (heat sink temperature), 12 (general-purpose output YA0)
00 (output frequency), 01 (output current),
02 (output torque), 04 (output voltage), 05 (input power), 06
(electronic thermal overload), 07 (LAD frequency),
09 (motor temperature), 10 (heat sink temperature),
11 (output torque [signed value]), 13 (general-purpose output YA1)
00 (output frequency), 01 (output current),
02 (output torque), 04 (output voltage), 05 (input power), 06
(electronic thermal overload), 07 (LAD frequency),
09 (motor temperature), 10 (heat sink temperature),
14 (general-purpose output YA2)
0.20 x "rated current" to 1.50 x "rated current" (A)
(Current with digital current monitor output at 1,440 Hz)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
4 - 11
Chapter 4 List of Data Settings
Default
FF FEF
01
00
03
07
40
05
00
00
00
Rated current
00
00
00
00
00
01
Change during
RUN operation
FUF b031≠10 b031=10
Not Not
Not Not
Not Not
Not Not
Not Not
Not Not
Not Not
Not Not
Not Not
Allowed Allowed
Not Not
Not Not
Not Not
Not Not
Not Not
Not Not