Table of Contents
Advertisement
Procedure for directly specifying or selecting a code
- You can specify or select a code or data by entering each digit of the code or data instead of scrolling codes or
data in the monitor, function, or extended function mode.
- The following shows an example of the procedure for changing the monitor mode code "d001" displayed to
extended function code "A029":
1) Display the monitor mode code.
("d001" is displayed.)
STOP/
RUN
RESET
(*2)
FUNC
(*3)
Press the
and
1
FUNC
together.
2) Change to the extended function mode.
RUN
STOP/
RESET
FUNC
- Character "d" in the leftmost digit (fourth digit
from the right) starts blinking.
1
Press the
("A001" is displayed.)
(*3)
STOP/
RUN
RESET
FUNC
- Character "A" is blinking.
- Pressing the [STR] key determines the blinking
character.
(*2)
STR
Press the
FUNC
(to determine character "A").
3) Change the third digit of the code.
STOP/
RUN
RESET
FUNC
- Character "0" in the third digit is blinking.
- Since the third digit need not be changed,
press the [STR] key to determine the character
"0".
(*2)
STR
- Character "9" in the first digit is blinking.
keys
2
(*1)
5) Change the first digit of the code.
STR
- Character "1" in the first digit is blinking.
key twice.
(*2)
FUNC
(*2)
STR
- Character "2" in the second digit is
blinking.
key
4) Change the second digit of the code.
Press the
STR
key.
(Character "0" is
determined.)
STR
(*2)
FUNC
- Character "0" in the second digit is
blinking.
6) End the change of the extended function code.
("A029" is displayed.)
Press the
key.
STOP/
RUN
RESET
STR
FUNC
(Character "9"
is determined.)
1
Press the
key eight times or
the
key twice.
2
STOP/
RUN
RESET
FUNC
STR
Press the
STR
key.
("A021" is displayed.)
STOP/
RUN
RESET
FUNC
STR
Press the
key twice.
1
RUN
STOP/
RESET
FUNC
STR
3 - 7
Chapter 3
Operation
STR
STOP/
RUN
RESET
FUNC
STR
- Selection of code "A029" is completed.
* If a code that is not defined in the code list or
not intended for display is entered, the
leftmost digit (fourth digit) (character "A" in
this example) will start blinking again.
In such a case, confirm the code to be entered
and enter it correctly. For further information,
refer to Section 4.2.84. " Function code
display restriction," (on page 4-79), Section
4.2.85, "Initial-screen selection," (on page
4-81), Section 4.2.86, "Automatic
user-parameter setting," (on page 4-82), and
Chapter 8, "List of Data Settings."
7) Press the
FUNC
key to display the data
corresponding to the function code, change
1
the data with the
and/or
2
key, and then press the
store the changed data. (*4)
Note that you can also use the procedure
(steps 1) to 6)) described here to change the
data. (*3)(*4)
*1
This procedure can also be used on screens
displaying a code other than "d001".
*2
FUNC
If the
key is pressed while a digit is
blinking, the display will revert to the
preceding status for entering the digit to the
right of the blinking digit.
*3
FUNC
If the
key is pressed while the leftmost
(fourth) digit is blinking, the characters
having been entered to change the code will
be cancelled and the display will revert to the
original code shown before the
keys were pressed in step 1).
*4
When changing data, be sure to press the
key first.
FUNC
STR
key to
1
and
2
Advertisement
Table of Contents
