Download Print this page

Sargent Profile Series Installation Instructions Manual

Hardwired networked cylindrical lock
Hide thumbs Also See for Profile Series:

Advertisement

FCC Part 15
Transmitter Certification
Test Report
FCC ID: SPI-4XXKPMR
FCC Rule Part: 15.209
ACS Report Number: 05-0270-15C
Manufacturer: Single Access Lock Inc.
Model: 4XXKP/MR
Installation Guide(s)
5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598

Advertisement

loading
Need help?

Need help?

Do you have a question about the Profile Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Sargent Profile Series

  • Page 1 FCC Part 15 Transmitter Certification Test Report FCC ID: SPI-4XXKPMR FCC Rule Part: 15.209 ACS Report Number: 05-0270-15C Manufacturer: Single Access Lock Inc. Model: 4XXKP/MR Installation Guide(s) 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598...
  • Page 2 Installation Instructions For Profile Series Hardwired Networked v.S1 Cylindrical Lock A7763A 10/04...
  • Page 3: Table Of Contents

    Cet appareil numérique de la classe B est conforme avec la norme NMB-003 du Canada. Warning To comply with “Fire Listed” doors, battery operated units must be replaced with alkaline batteries only. For installation assistance, contact SARGENT at 800-810-WIRE (9473)
  • Page 4: General Description

    It is a self-contained microprocessor-controlled keypad with non-volatile memory. The keypad will hold a total of 2000 (S1-LU, S1-PK, S1-PA) different user codes. This product is operated by six (6) “AA” alkaline batteries or by the SARGENT 3267 9VDC power supply. Specifications •...
  • Page 5: Parts Breakdown

    Profile Series v. S1 Cylindrical Lock Parts Breakdown Optional For installation assistance, contact SARGENT at 800-810-WIRE (9473)
  • Page 6 Screw Pack – Specify Finish (Strike Screws, Latch Screws, Push Pin Tool, Strike Box) 52-0253 Battery Keeper See Item # 20 Screw Pack See Item # 20 Screw Pack 52-3010 Power/Data Cable (Not Shown) 52-3211 Door Position Harness (Not Shown) 52-2847 Weather Conduit (Not Shown) For installation assistance, contact SARGENT at 800-810-WIRE (9473)
  • Page 7: Installation Instructions

    (2) 1/8" Dia. holes required 7/8" C L of 1-1/2" Dia. 1-1/2" Latchbolt door prep Through-bolt Lockbody hole (2) hole Pre-drilled and/or tapped holes 2 places Outside Inside of door of door Wood Door Preparation For installation assistance, contact SARGENT at 800-810-WIRE (9473)
  • Page 8 #8 x 1/2" long for wood & metal doors Through-bolt hole (2) IMPORTANT: Latch bevel must match door bevel and deadlocking latch must stop on strike when door is closed Strike Deadlocking latch For installation assistance, contact SARGENT at 800-810-WIRE (9473)
  • Page 9 3. Lock body must engage both the latch unit prongs and tail piece, as shown. For wood door only Inside of door Screws partially tightened IMPORTANT: IMPORTANT: Lockbody Door must remain open must be centered during installation. in the door Use door stop. For installation assistance, contact SARGENT at 800-810-WIRE (9473)
  • Page 10 2. Remove key and cylinder from lever. 3. Insert new cylinder.* Cylinder 4. Secure by pressing cylinder retainer flush with self.* Washers (only 30- prefix) * NOT SHOWN For installation assistance, contact SARGENT at 800-810-WIRE (9473)
  • Page 11 6. Tighten two latch screws completely. Figure 2 Figure 1 8-32 Flat head screw Keypad harness Ground wire Lockbody Inside of harness door Inside lever Figure 3 Inside rose * NOT SHOWN For installation assistance, contact SARGENT at 800-810-WIRE (9473)

This manual is also suitable for:

V.s1