Chapter 5 Troubleshooting; Troubleshooting Of Emitter - Panasonic SF4B V2 Series Instruction Manual

Light curtain type 4
Hide thumbs Also See for SF4B V2 Series:
Table of Contents

Advertisement

Chapter 5 Troubleshooting

<Reference>
Check the wiring.
Check the power supply voltage and the power supply capacity.

5-1 Troubleshooting of Emitter

<All indicators are OFF>
Power is not being supplied
6XSSO\ YROWDJH LV RXW RI WKH VSHFL¿HG UDQJH
Connector is not connected securely.
<Fault indicator (yellow) lights or blinks>
[Digital error indicator: ]
Setting data error of this device
[Digital error indicator: ]
System error between emitter
and receiver
[Digital error indicator: ]
Series connection error
[Digital error indicator: ]
No. of total units / No. of total
beam channels error
[Digital error indicator: ]
Interlock setting error
[Digital error indicator: , ]
Muting lamp error
© Panasonic Industriar Devices SUNX Co., Ltd. 2012 ME-SF4BV2-05
Cause
Cause
S e r i e s c o n n e c t i o n i s i n -
correct.
Noise is out of the specified
range.
Internal error
Systems are different be-
tween emitter and receiver.
The serial signal short-circuits
or comes down.
Any of the main / sub sensor
is in error.
No. of total units / No. of total
beam channels is out of the
VSHFL¿HG UDQJH
Voltage level of interlock set-
ting input wire (pale purple),
or emission halt input / reset
input wire (pink) is unstable.
Muting lamp output wire (red)
short-circuits with 0V or +V.
Muting lamp output wire (red)
short-circuits with other I/O
wires.
Excessive incoming current
ÀRZV LQ WKH PXWLQJ ODPS RXW-
put.
Output polarity setting wire
(shield) and muting lamp
output wire (red) are not cor-
rectly wired.
Output circuit error
Remedy
&KHFN WKDW WKH SRZHU VXSSO\ FDSDFLW\ LV VXI¿FLHQW
Connect the power supply correctly.
Set the supply voltage correctly.
Connect the connector securely.
Remedy
Check that the cable for series connection does
not short-circuit, or is connected to the correct po-
sition (emitter for emitter, receiver for receivers).
Incase the handy controller (SFB-HC) (optional)
is applied, reset the function.
Check the noise status around this device.
In case the handy controller (SFB-HC) (optional)
is applied, reset the function.
&RQWDFW RXU RI¿FH
Set the same value to the numbers of emitter and
receiver and that of beam channel, and the shield
wires.
&KHFN LI WKH HQG FDS KDV EHHQ ¿WWHG SURSHUO\
Check that the cable for series connection does
not short-circuit, or is connected to the correct
position (emitter for emitter, receiver for receiver).
Check the error contents of the device connected
by the cable for series connection.
Set the condition of the series connection within
WKH VSHFL¿FDWLRQ
Refer to "2-5-6 Series Connection."
Wire the interlock setting input wire (pale purple)
and emission halt input / reset input wire (pink)
correctly.
Wire the muting lamp output wires (red) correctly.
Refer to "2-5 Wiring."
&XUUHQW YDOXH VKRXOG EH ZLWKLQ WKH VSHFL¿HG PXW-
ing lamp output.
Wire the output polarity setting wire (shield) cor-
UHFWO\ 9 313 RXWSXW 9 131 RXWSXW 
Wire the muting lamp output wire (red) correctly.
Refer to "2-5 Wiring."
Output circuit is damaged. Replace this device.
80

Advertisement

Table of Contents
loading

This manual is also suitable for:

Sf4b-f*v2Sf4b-h*v2Sf4b-a*v2

Table of Contents