Preventive Maintenance And Inspection Schedule; Maintenance And Inspection Schedule Codes; Footnotes - JLG 1932RS/6RS Service And Maintenance Manual

SECTION 2 - GENERAL
Type
Pre-Start
Inspection
Pre-Delivery
Inspection
Frequent In service for 3 months or 150 hours, whichever comes first; or Out of
Inspection service for a period of more than 3 months; or Purchased used.
Annual Machine
Inspection Annually, no later than 13 months from the date of the prior inspection. Owner, Dealer, or User
Preventative Main-
At intervals as specified in the Service and Maintenance Manual.
tenance
2.2 PREVENTIVE MAINTENANCE AND INSPECTION
SCHEDULE
The preventive maintenance and inspection checks are listed
and defined in the following table. This table is divided into
two basic parts, the "AREA" to be inspected and the "INTER-
VAL" at which the inspection is to take place. Under the "AREA"
portion of the table, the various systems along with the com-
ponents that make up that system are listed. The "INTERVAL"
portion of the table is divided into two columns representing
the various inspection time periods. The numbers listed within
the interval column represent the applicable inspection code
for which that component is to be checked.
The checks and services listed in this schedule are not
intended to replace any local or regional regulations that may
pertain to this type of equipment nor should the lists be con-
sidered as all inclusive. Variances in interval times may occur
due to climate and/or conditions and depending on the loca-
tion and use of the machine.
JLG INDUSTRIES REQUIRES THAT A COMPLETE ANNUAL INSPECTION BE PER-
FORMED IN ACCORDANCE WITH THE "ANNUAL MACHINE INSPECTION
REPORT" FORM.
NOTE: This machine requires periodic safety and maintenance
inspections by a qualified JLG mechanic. Notify JLG dealer
if inspection is overdue.

Maintenance and Inspection Schedule Codes:

1. Check for proper and secure installation.
2. Visual inspection for damage, cracks, distortion, or exces-
sive wear.
3. Check for proper adjustment.
4. Check for cracked or broken welds.
5. Operates properly.
2-2
Table 2-1. Inspection and Maintenance Responsibilities
Frequency
Prior to use each day; or
At each Operator change.
Prior to each sale, lease, or
rental delivery.
Primary Service
Responsibility Qualification
User or Operator User or Operator
Owner, Dealer, or User Qualified JLG Mechanic
Owner, Dealer, or User Qualified JLG Mechanic
Factory-Trained
Service Technician
(recommended)
Owner, Dealer, or User Qualified JLG Mechanic
6. Returns to neutral or "off" position when released.
7. Clean and free of debris.
8. Interlocks function properly.
9. Check for signs of leakage.
10. Decals installed and legible.
11. Check for proper fluid level.
12. Check for chafing and proper routing.
13. Check for proper tolerances.
14. Properly lubricated.
15. Torqued to proper specification.
16. No gouges, excessive wear, or cords showing.
17. Properly inflated and seated around rim.
18. Proper and authorized components.
19. Fully charged.
20. No loose connections, corrosion, or abrasions.
21. Verify.
22. Perform.
23. Sealed properly.
24. Overrides Platform controls.
25. Remove pump motor cover and blow away any brush
wear dust from cover, brushes, and brush holder assem-
bly.

Footnotes:

(a) Prior to each sale, lease, or delivery
(b) In service for 3 months; or Out of service for 3 months
or more; or Purchased used
(c) Annually, no later than 13 months from the date of the
prior inspection
Reference
Operation and Safety Manual
Service and Maintenance Manual and
applicable JLG inspection form.
Service and Maintenance Manual and
applicable JLG inspection form.
Service and Maintenance Manual and
applicable JLG inspection form.
Service and Maintenance Manual
3121273