Nice E SMART XSI 0628 DC Instructions And Warnings For Installation And Use
Tubular motor
Hide thumbs
Also See for E SMART XSI 0628 DC:
Subscribe to Our Youtube Channel
Related Manuals for Nice E SMART XSI 0628 DC
Summary of Contents for Nice E SMART XSI 0628 DC
- Page 1 Nice E SMART XSI 0628 DC E SMART XSI 0820 DC Tubular Motor EN - Instructions and warnings for installation and use...
-
Page 2: Installation Warnings
GENERAL WARNINGS: SAFETY - INSTALLATION - USE (original instructions in Italian) ATTENTION Important safety instructions. Follow all instructions as improper installation may cause serious damage ATTENTION Important safety instructions. It is important for you to comply with these instructions for your own and other people’s safety. -
Page 3: Product Description And Intended Use
The motor is equipped with three separate cables: one power cable, one com- awning travel, immediately blocking the movement in progress and performing a mand cable and one Nice smart-bus data cable. Each cable has a connector for brief inversion of movement. The same system is automatically activated at the end connection to the motor (fig. - Page 4 100-240 Vac 100-240 Vac 50/60 Hz 50/60 Hz LIGHT SENSOR Com. Step by Step (▲ ■ ...) ■ 24 Vdc Com. 100-240 Vac DRY CONTACT DRY CONTACT 50/60 Hz THE POWER CABLE IS REMOVABLE LEGEND Electronic motor head Limit switch adjustment buttons Power cable Double button A1 = Red wire...
-
Page 5: Ce Declaration Of Conformity
Type of product: Tubular gearmotor for indoor roll-up awnings and sunscreens Group D – using a smart- Programming with a smartphone Model / Type: E SMART XSI 0628 DC, E SMART XSI 0820 DC with NFC (Near Field Commu- phone. nication). This technology is not Accessories: –... - Page 6 –– GROUP “A” PROCEDURES –– only possible using the Nice "ERA" Series DMBM module GENERAL WARNINGS RELATING TO THE PROCEDURES OF PROGRAMMING • Refer to the DMBM module's own manual to perform any procedure from Group “A”. Only the “Notes and Warnings” for each procedure are given below.
- Page 7 TYPE A • To start a movement: to raise the awning press s; to lower it press t. – standard Nice operation for “ERA” • To stop the movement: press the opposite button from that used to start the movement.
- Page 8 (procedure A.9) may set the cruise speed outside the allowed range (given in “Tech- nical specifications”). If so, the motor will report the error by means of the “Nice Screen Configuration Tool” at the end of the procedures (A.1 / A.2 / A.9), and will automatically restore the nominal cruise speed.
- Page 9 NOTES AND WARNINGS • To run the procedures in this group, you must use a compatible programmer (see the “Nice Screen” catalogue, also available on www.niceforyou.com). • For the programming and adjustment procedures possible with a given programmer, see the programmer’s user manual and interface.
- Page 10 The programming with the “NFC” technology is not yet available on this motor. For more information contact the Nice Technical Assistance. Using a smartphone equipped with NFC technology and a software application produced by Nice (to be installed on your smartphone), you can configure the motors before installing them, even without the need to supply power.
- Page 11 Note: • All technical specifications stated herein refer to an ambient temperature of 20° C (± 5° C). • Nice S.p.A. reserves the right to apply modifications to products at any time when deemed necessary, maintaining the same intended use and func- The motor repeats the report message on the status of the installation by performing tionality.
- Page 12 Appendix Limit switch gear wheel (not included). Drive wheel (not included).
- Page 13 10 mm 2 screws: self-tapping without point, Motor bracket (not included in for plastic materials. Diameter: 3,5 mm; the package). length of threaded part: = min. 5 mm - max 8 mm Cable for connecting the POWER Supporting bracket of the winder roller (not included in the pack- age).
- Page 14 Nice S.p.A. Via Pezza Alta, 13 31046 Oderzo TV Italy www.niceforyou.com info@niceforyou.com...
Need help?
Do you have a question about the E SMART XSI 0628 DC and is the answer not in the manual?
Questions and answers