Directed DS4+ Installation Manual
  1. Manuals
  2. Brands
  3. Directed Manuals
  4. Automobile Accessories
  5. DS4+
  6. Installation manual
Directed DS4+ Installation Manual

Directed DS4+ Installation Manual

Gm9
Hide thumbs Also See for DS4+:
Table of Contents

Advertisement

Quick Links

See also: Installation Manual
INSTALLATION GUIDE
GM9
Designed by Installers for Installers
© 2017 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle's
electrical system and components.
2017-08-25
DS4+

Advertisement

Table of Contents
loading

Related Manuals for Directed DS4+

Summary of Contents for Directed DS4+

  • Page 1 INSTALLATION GUIDE Designed by Installers for Installers © 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical system and components.

  • Page 2: Table Of Contents

    Contents Warning! Safety first ........................3 Introduction ............................ 4 Pre-installation and application warnings ..................4 Vehicle application guide ......................5 Wiring connections ......................... 6 Main harness (H1), 12-pin black connector .................. 6 Relay harness (H2), 10-pin white connector .................. 6 Data harness (H3), 8-pin white connector ..................

  • Page 3: Warning! Safety First

    The following safety warnings must be observed at all times: • Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. • When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation.

  • Page 4: Introduction

    The siren is ONLY required when enabling the security features during module flashing. Required ONLY for manual transmission vehicles. Additional parts required (maximum required): Resistor 100Ω Fuse 7.5A Diode 6A 0 x 1A Diodes 1 x 180Ω Resistor 0 x Fuse 0 x Relay DS4+ GM9 © 2017-08-25 Directed. All rights reserved.

  • Page 5: Vehicle Application Guide

    DL: OE Door Lock & Alarm Controls FOB: Sync CAN Interface w/ FOB Remote PK: Transponder & Immobilizer Override RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status DS4+ GM9 © 2017-08-25 Directed. All rights reserved.

  • Page 6: Wiring Connections

    (MUX) Brake Activation Output H3/7 Orange/Black No Connection H3/8 Yellow/Black Immo.Data (connector side) If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. DS4+ GM9 © 2017-08-25 Directed. All rights reserved.

  • Page 7: Analog Input/Output Harness (H4), 22-Pin White Connector

    If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. DS4+ GM9 © 2017-08-25 Directed. All rights reserved.

  • Page 8: Installation (Wiring Diagrams, Fuse Selection & Vehicle Wiring Reference Charts)

    (-) Clutch Output: Lt. Green: 8 (-) Ground: Black: 10 Clutch Switch (black 3-pin Slide connector) DS4+ to open Clutch: Pin B It is important to check that the fuses are positioned correctly. DS4+ GM9 © 2017-08-25 Directed. All rights reserved.
  • Page 9 Dk. Blue Data BCM under drivers dash. Blue Dk. Blue/ HS CAN Low Data BCM under drivers dash. Blue Yellow Brake Yellow BCM under drivers dash. Blue Red/Violet BCM under drivers dash. Blue DS4+ GM9 © 2017-08-25 Directed. All rights reserved.
  • Page 10 HS CAN High Lt. Blue Data BCM under drivers dash. Blue HS CAN Low White Data BCM under drivers dash. Blue Brake Blue/Yellow BCM under drivers dash. Blue Red/Violet BCM under drivers dash. Blue DS4+ GM9 © 2017-08-25 Directed. All rights reserved.
  • Page 11 HS CAN High Blue Data BCM under drivers dash. Blue HS CAN Low White Data BCM under drivers dash. Blue Brake Blue BCM under drivers dash. Blue Red/Violet BCM under drivers dash. Blue DS4+ GM9 © 2017-08-25 Directed. All rights reserved.

  • Page 12: Type 2

    (-) Clutch Output: Lt. Green: 8 (-) Ground: Black: 10 Clutch Switch (black 3-pin Slide connector) DS4+ to open Clutch: Pin B It is important to check that the fuses are positioned correctly. DS4+ GM9 © 2017-08-25 Directed. All rights reserved.
  • Page 13 HS CAN Low White Data BCM under driver dash. White SW CAN Green Data BCM under driver dash. Gray Brake White/Green BCM under driver dash. Blue Red/Violet BCM under driver dash. Blue DS4+ GM9 © 2017-08-25 Directed. All rights reserved.
  • Page 14 HS CAN Low White Data BCM under driver dash. White SW CAN Green Data BCM under driver dash. Gray Brake White/Green BCM under driver dash. Blue Red/Violet BCM under driver dash. Blue DS4+ GM9 © 2017-08-25 Directed. All rights reserved.

  • Page 15: Type 3

    Immo. Data Interrupt (conn.side): Blue: 3 (+) 12V Input: Red: 6 & 12 (-) Ground: Black: 10 Slide DS4+ to open It is important to check that the fuses are positioned correctly. DS4+ GM9 © 2017-08-25 Directed. All rights reserved.
  • Page 16 Data BCM passenger side center console. White SW CAN Green Data BCM passenger side center console. Blue Brake Blue/Yellow BCM passenger side center console. Blue Red/Brown BCM passenger side center console. Blue DS4+ GM9 © 2017-08-25 Directed. All rights reserved.

  • Page 17: Key2Go

    Any first-time user must re-register to gain access to Key2GO, and some additional information will be required to complete the registration process, such as your Directed account number and store name. Key2GO is compatible with XKLoader2 and the online web tool, as well as XKLoader3 and the Directechs Mobile application.

  • Page 18: When Used In Conjunction With Smartstart

    SmartStart. To ensure proper functionality with SmartStart, it is important that it is selected in the system programming of the DirectLink application or via the online web tool. Note: Both black D2D ports are reserved for the Control Center (antenna) and 8504D Combo Sensor. DS4+ GM9 © 2017-08-25 Directed. All rights reserved.

  • Page 19: Module Programming

    By default, the tachometer is preprogrammed for the vehicle. For instructions on how to Initialize tachometer program tach, see page 24. * Your aftermarket remote may differ from the model shown in the illustrations. You have successfully completed the module programming sequence. DS4+ GM9 © 2017-08-25 Directed. All rights reserved.

  • Page 20: Keyport Location

    GMC Yukon 2015-2016 Open the center console and place the transmitter in the transmitter pocket with the buttons facing the front of the vehicle. Cupholder Center Console DS4+ GM9 © 2017-08-25 Directed. All rights reserved.

  • Page 21: Led Diagnostics And Troubleshooting

    External module synchronization Description Troubleshooting OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. (Flashes red, red, then orange) x 10 DS4+ GM9 © 2017-08-25 Directed. All rights reserved.
  • Page 22 The vehicle was detected as moving, which prevents the system from shutting it down. Flashes red x 4 Analog error codes Description Troubleshooting DEI feature error. A feature config file mismatch was detected. Please contact Technical Support. Flashes red, green & orange DS4+ GM9 © 2017-08-25 Directed. All rights reserved.

  • Page 23: Soft Reset

    After 3 seconds the LED turns ON solid orange. Keep holding the programming button until & & the LED flashes red, then orange slowly. Solid Hold Flashes Release the programming button. The LED turns ON solid red. & Release Solid DS4+ GM9 © 2017-08-25 Directed. All rights reserved.

  • Page 24: Learning The Tach (Not Needed With Virtual Tach)

    Important! After successfully learning Virtual Tach, a small minority of vehicle starters may over crank or under crank during remote start. Use the VirtualTach Fine tune feature in the configuration wizard to adjust the starter output time in 50mS increments to compensate for such an occurrence. DS4+ GM9 © 2017-08-25 Directed. All rights reserved.

  • Page 25: Limited Lifetime Consumer Warranty

    Directed dealer, the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number and address;...

  • Page 26: Quick Reference Guide

    Factory remote. Press the Remote Start button on the transmitter.* • Aftermarket remote. • Directed SmartStart application via your smartphone. & The parking lights will flash once to indicate the Parking lights flash x1 Press Remote vehicle is now in Pit Stop Mode.
  • Page 27 SmartStart compatible Notes This system is compatible with Directed SmartStart. For a complete list of supported features, please visit www.mysmartstart.com. What is SmartStart? Now you can remote start, lock and unlock your car just by pushing a button on your smartphone;...

Table of Contents