Parameter Of Hard Limit Function(16 In Total); Parameter Of Hard And Soft Limit Function (9 In Total); System Parameter(11 In Total) - Digital Dream DM500 User Manual

10) Parameter of hard limit function(16 in total)

Para.
Parameter definition
Mark
#400 enable X-- limit
#401 enable Y-- limit
#402 Enable Z-- limit
#403 enable A-- limit
#404 enable X++ limit
#405 enable Y++ limit
#406 enable Z++ limit
#407 enable A++ limit
#408 Electric level X-- limit
#409 Electric level Y-- limit
#410 Electric level Z-- limit
#411 Electric level A-- limit
#412 Electric level X++ limit
#413 Electric level Y++ limit
#414 Electric level Z++ limit
#415 Electric level A++ limit

11) Parameter of hard and soft limit function (9 in total)

Para.
Parameter definition
Mark
#374 enable Soft Limit
#375 value of X-- Soft Limit
#376 value of Y-- Soft Limit
#377 value of Z-- Soft Limit
#378 value of A-- Soft Limit
#379 value of X++ Soft Limit
#380 value of ++ Soft Limit
#381 value of Z++ Soft Limit
#382 value of A++ Soft Limit

12 ) System parameter(11 in total)

Para.
Parameter definition
Mark
Interface response speed
#2
while processing
#88 Enable of beep
#114 Enable of Cont and Step Mode
#115 Coordinate unit selection
#120 U disk partition type
#218 Cycle Start key mode selection
#249 Time of the Logo Display
#495 circle of interpolation
#250 enable of draw tool road
#253 mode of draw
#495 Interpolation period
Default Parameter Parameter
value Unit Scope
1 BOOL
1 BOOL
1 BOOL
1 BOOL
1 BOOL
1 BOOL
1 BOOL
1 BOOL
0 BOOL
0 BOOL
0 BOOL
0 BOOL
0 BOOL
0 BOOL
0 BOOL
0 BOOL
Default Parameter Parameter
value Unit Scope
0 BOOL
-400 BOOL -2000~0
-400 BOOL -2000~0
-400 BOOL -2000~0
-400 BOOL -2000~0
400 BOOL 0~2000
400 BOOL 0~2000
400 BOOL 0~2000
400 BOOL 0~2000
Default Parameter Parameter
value Unit Scope
400 BOOL 400-10000
1 BOOL
0 BOOL
0 BOOL
0 BOOL
0 BOOL
2 s 0.1-10
0.002 s 0.002-0.01
1 BOOL
0 BOOL
0.005 s 0.002~0.01
Page -40
Notes
1/0 0：Disable 1：Enable
1/0 0：Disable 1：Enable
1/0 0：Disable 1：Enable
1/0 0：Disable 1：Enable
1/0 0：Disable 1：Enable
1/0 0：Disable 1：Enable
1/0
0：Disable 1：Enable
1/0 0：Disable 1：Enable
1/0 1: High; 0:Low
1/0 1: High; 0:Low
1/0 1: High; 0:Low
1/0 1: High; 0:Low
1/0 1: High; 0:Low
1/0 1: High; 0:Low
1/0 1: High; 0:Low
1/0 1: High; 0:Low
Notes
1/0 0:Disable, 1:Enable
The set value will trigger the limit signal.
The limit values refer to the machine
coordinates, not the work piece coordi-
nate.
The set value will trigger the limit signal.
The limit values refer to the machine
coordinates, not the work piece coordi-
nate.
Notes
Note: For general G-code file, the
parameter can be set as 400. If the file
has many small segments, adjust the
parameter to be larger.
1/0 0:Disable,1:Enable
1/0 0:Enable,1:Disable
1/0 0:Metric; 1:Imperical
1/0 0: partitions; 1: no partitions
1/0 0: pause&start; 1: restart
circle of interpolation
1/0 0:disable 1: enable
1/0 0:statue mode 1:line mode
DM500 User's Manual