ETC Source Four Mini LED User Manual
Hide thumbs
Also See for Source Four Mini LED:
- User manual (20 pages) ,
- Installation manual (4 pages) ,
- User manual (12 pages)
Subscribe to Our Youtube Channel
Related Manuals for ETC Source Four Mini LED
Summary of Contents for ETC Source Four Mini LED
- Page 1 ™ Source Four Mini User Manual Part Number: 7063M1220 Rev: D Released: 2017-04...
- Page 2 All other trademarks, both marked and not marked, are the property of their respective owners. ETC intends this document, whethe r printed or electronic, to be provided in its entirety. This pr oduct is intended for professional use only. Read this entire document before using this product.
-
Page 3: Table Of Contents
Table of Contents Introduction ..... . . 1 Basic assembly ..... . 2 Installing a lens tube. - Page 4 Table of Contents...
-
Page 5: Introduction
Introduction The Source Four Mini LED has three available mounting options. The portable fixture includes a miniature C-clamp and yoke-mounted driver. The canopy- mount fixture and track-mount fixture both include an integral driver. There are four lens tube sizes available for each mounting option: 19°, 26°, 36°, and 50°. -
Page 6: Basic Assembly
3) Do not look directly at lighted lamp. 4) Keep lamp away from materials that may burn. 5) External temperature after 5 minutes of full-brightness operation 50°C (122°F). 6) External temperature when steady state is achieved 67°C (152.6°F). SAVE THESE INSTRUCTIONS Source Four Mini LED User Manual... -
Page 7: Installing A Lens Tube
Installing a lens tube A lens tube must be installed prior to use of the Source Four Mini LED. There are four lens tube sizes available: 19°, 26°, 36°, and 50°. Beam focus knob Unscrew the beam focus knob from the loose lens tube. -
Page 8: Installing A Canopy Fixture
Remove the mounting plate from the fixture by removing the two canopy screws and the ground screw. Set the ground screw safely aside. Using the mounting plate screws, secure the mounting plate to the installed electrical box, which is not included. Source Four Mini LED User Manual... - Page 9 Open all four of the shutter blades by sliding them outward until they stop. Install a gobo and gel as desired and confirm that they are properly secured. Restore power at the main fuse. Focus the fixture as desired. Source Four Mini LED User Manual...
-
Page 10: Installing A Track Fixture
Lock the fixture into place using the yoke lock. Cable protection posts on both the yoke lock and the yoke prevent the fixture from rotating a full 360°. To lock the yoke in place use a 1.5 mm Allen wrench. Source Four Mini LED User Manual... -
Page 11: Using The Ad1 Track Adapter
ETC offers the option of installing a track-mounted fixture with an adapter that is compatible with Halo Track Systems. Halo Track Systems are not available from ETC, but the Source Four Mini LED fixture can be custom- ordered from ETC with the AD1 track adapter. -
Page 12: Adjustments
Adjustments Adjusting the yoke position The Source Four Mini LED provides multi-positioning capabilities within its yoke for overall fixture angle. Setting the angle with the yoke Yoke locking knob Loosen the yoke locking knob. Do not remove the knob. Tilt the fixture to the desired position. -
Page 13: Focusing The Beam
Shaping the beam Shape the beam with the four shutters or with a pattern. The Source Four Mini LED has four shutters: left, right, top, and bottom. Each shutter can be pulled out or pushed in to create the desired beam shape. -
Page 14: Projecting A Pattern
Projecting a pattern The Source Four Mini LED has a pattern holder slot on the top side of the shutter barrel, in front of the shutter. It accommodates an E-size (37.5 mm with a 25.4 mm image area) pattern holder. -
Page 15: Adjusting The C-Clamp On The Portable Fixture
CAUTION: Tighten the C-clamp pipe bolt to about 18 in/lb (approximately finger tight plus up to one-quarter turn). Do not use excessive force. Note: The Source Four Mini LED yoke has a C-clamp hole with a .406” diameter. Cleaning the glass lens... - Page 16 Web: etcconnect.com Copyright © 2017 Electronic Theatre Controls, Inc. All Rights Reserved. Product information and specifications subject to change. ETC intends this document to be provided in its entirety. 7063M1220 Rev D Released 2017-04 ...
Need help?
Do you have a question about the Source Four Mini LED and is the answer not in the manual?
Questions and answers