Sharp MX-B350W User Manual page 256

SYSTEM SETTINGS►SYSTEM SETTINGS
FW. RX Data
This setting is used to select whether or not received
faxes are forwarded to a fax machine programmed as
explained in Received Data FW. Station Set (page 7-22)
in the event that the machine cannot print the faxes. The
setting is initially disabled.
• The setting is enabled and a checkmark appears in
the checkbox.
• If the procedure is performed when the setting is
enabled, the checkmark will be cleared and the setting
disabled.
This setting only operates when the fax number of the
machine that is to receive the forwarded faxes is
programmed.
Received Data FW. Station Set
When a problem prevents the machine from printing a
received fax, the fax forwarding function
can be used to forward the received fax to another fax
machine. Use this setting to setting the fax number of the
destination fax machine. Only one fax number can be
programmed (maximum of 50 digits).
To delete the number, follow these steps:
(1) Select "Delete" and then press the [OK] key.
(2) Select "Delete" with the [ ] or [ ] key and then
press the [OK] key.
Anti Junk Fax
When this setting is enabled, reception from fax
numbers programmed using the
(page 7-22)" setting will be blocked.
This setting is normally disabled.
• The setting is enabled and a checkmark appears in
the checkbox.
• If this procedure is performed when the setting is
enabled, the checkmark will be cleared and the setting
disabled.
Enter Junk Fax #
This setting is used to program fax numbers from which
you wish to block reception. Up to 50 fax numbers can
be stored (maximum of 20 digits each). To block
reception from the programmed fax numbers, the "Anti
Junk Fax" setting must be enabled.
►page 4-47
"Enter Junk Fax #
7-22
To delete a number, follow these steps: Before
deleting a number, use the
check the control number that identifies the fax
number (01 to 50) that you wish to delete. The control
number must be entered to delete the fax number.
(The fax number will not appear in the display. If the
wrong control number is accidentally entered, a fax
number other than the fax number that you wish to
delete will be deleted.)
(1) Select "Delete" and then press the [OK] key.
(2) Select the 2-digit control number (01 to 50) that
identifies the fax number that you wish to delete
with the [ ] or [ ] key and then press the [OK]
key.
(3) Select "Delete" with the [ ] or [ ] key and then
press the [OK] key.
Polling Security
These settings are used for the public box.
Select the [Polling Security] to configure the settings.
Polling Security
When performing polling memory (see
access (polling security) (page
used to select whether any machine will be allowed to
poll your machine, or only machines that have been
programmed in your machine. Normally this setting is
enabled.
• The setting is enabled and a checkmark appears in
the checkbox.
• If this procedure is performed when the setting is
enabled, the checkmark will be cleared and the setting
disabled.
Polling Passcode # Mode
When "Polling Security" is enabled, use this setting to
program (or delete) the fax numbers of the machines
that are allowed to poll your machine. Programmed fax
numbers are called passcodes. Up to 10 fax numbers
can be programmed. To check the programmed
numbers, print the List Print (page
If you make a mistake, move the cursor to the mistake
with the [ ] or [ ] keys and enter the correct number.
To clear a passcode number, follow these steps:
(1) Select "Delete" and then press the [OK] key.
(2) Enter the control number that identifies the
number you wish to clear, and then press the [OK]
key.
(3) Select "Delete" with the [ ] or [ ] key and then
press the [OK] key.
List Setting (page 7-18) to
Restricting polling
4-36)), this setting is
7-15).