Visonic PowerMaster 360 Installer's Manual page 41

Option
TEST ALL DEVICES
TEST ONE DEVICE
→CONTACT SENSORS
→MOTION SENSORS
→GLASSBREAK SENS.
→SHOCK SENSORS
→SMOKE SENSORS
→CO SENSORS
→GAS SENSORS
→FLOOD SENSORS
→TEMPERATURE SENS.
→KEYFOBS
→PANIC BUTTONS
→KEYPADS
→SIRENS
→REPEATERS
SHOW ALL DEVICES
1
The signal strength indications are as follows: "STRONG"; GOOD"; "POOR"; "1-WAY" (the device operates in 1-way
mode or, the "NOW" communication test failed); "NOT TST" (results are shown without any performed test); "NOT
NET" [device is not networked (not fully enrolled)]; "NONE" (keyfob 24Hr result); or "EARLY" (result of the last 24Hrs
without statistics).
D-305735 PowerMaster 360 Installer's Guide
Instructions
You can test all wall-mounted devices automatically, one after the other, after which the
installer tests the other devices in the following order: vanishing magnetic contact
devices, keyfobs and then panic buttons.
While in "TEST ALL DEVICES", press
appear: "TESTING Xxx NNN", where "Xxx" indicates the type of device and "NNN" indicates
the number of enrolled devices in the panel that have not been tested yet. This number
automatically drops one count for every tested device.
Pressing any key during the testing process will open the following options:
1. Press to jump to the next device group. For example, from wall-mounted devices to
keyfobs.
2. Press to continue the testing process
3. Press to exit the test process.
When all wall-mounted devices have completed the test procedure, you can test vanishing
magnetic contact devices.
While in the vanishing test process, indicated by the corresponding display, for example,
"TEST VANISH NNN", momentarily open the door or window.
When all vanishing magnetic contact devices have been tested, you can test keyfobs.
While in the keyfobs test process, indicated by the corresponding display, for example,
"TEST KEYFOBS NN", press any key of the selected device to initiate the test.
When all keyfobs have been tested, you can test panic buttons.
While in the panic button test process, indicated by the corresponding display, for example,
"TEST PANIC BT. NN", press a button on the pendant.
At the end of the test process, the panel will present the following: "SHOW ALL DEVICES".
Press to view devices' status.
Note: Refer to "SHOW ALL DEVICES" section below for further information on device
status.
You can select a specific device group you wish to test, for example, Motion Sensors.
Press to enter the "TEST ONE DEVICE" sub menu and use
device families. Press
"MOTION SENSORS".
Note: If there is no enrolled device, "
The following screens will then appear: "Xxx:<device name>"
Where Xxx indicates the device number. You can now select a specific device.
Press to test the selected device. The following screen will appear: "TESTING Xxx 001".
While in the keyfobs, panic button or vanishing magnetic contact test process, indicated
by the corresponding display, for example, "Xxx ACTIVATE NOW", press any key of the
selected keyfob or panic button, or momentarily open the door or window to initiate the
test.
At the end of the test process, the panel will present the devices' status:

1
"Xxx: 24hr: <status>"
Note: Refer to "SHOW ALL DEVICES" section for further information on device status.
You can view the devices status.
Note: This option is available only after testing process was done.
Press to view the devices' status.
The following screens will appear: "Xxx: 24hr: <status>"
Use to scroll between the device's families.
to initiate the test. The following screen will
to enter the <device family> sub menu, for example:
NO EXISTING DEV.
1
"Xxx: NOW: <status>" .
4. PROGRAMMING
to scroll through the
" will be displayed.

"<location>"

1
"Xxx: NOW: <status>"
1
41