Control Command - FOR-A MFR-1616 Operation Manuals

4-3. Control Command

The control command list below shows the standard control commands for Crosspoint remote
control and Crosspoint remote control 2 protocols, which are available for both LAN and
serial interfaces.
 Control command list
1 Commands (S?) for requesting the crosspoints list
2 Commands (X?) for requesting information on
crosspoints
(by specifying a destination and level.)
3 Commands (X:) for switching over a crosspoint (single
channel)
4 Commands for switching over crosspoints
(multi-channel simultaneous switchover)
5 Commands (W:) for locking a destination
6 Commands (z:) for reinitializing a unit
7 Commands (K?) for requesting input/output channel
names
8 Commands (A?) for requesting CPU status.
9 Commands (W?) for requesting destination lock status
(destination needs to be specified).
11 Commands for requesting System Size
12 Commands for setting video format (reference and/or
switching point).
*1 When commands are sent via LAN, an Echo, Prompt, S response and other response messages may be
included in a single packet or divided into two or more packets. Therefore, do not process commands in a per
packet basis but a per stream basis.
*2 A command protocol should be selected in the [Web-based Control: Port Settings page].
 Command formats
Func. Control command
1 @[sp]S?<Lvl>
2 @[sp]X?<Lvl><Dest>
3 @[sp]X:<Lvls>/<Dest>,<Src>
4 Clear a preset crosspoint.
@[sp]B:C
Preset a crosspoint.
@[sp]P:<Lvl>/<Dest>,<Src>
Read a preset crosspoint
specifying a level and destination.
@[sp]P?<Lvl><Dest>
Read preset crosspoints for all
channels in the specified level.
@[sp]V?<Lvl>
Perform the preset crosspoints
simultaneously.
@[sp]B:E
5 LOCK ALL units.
@[sp]W:<Lvl>/<Dest>,<ID>,1
LOCK OTHER units.
@[sp]W:<Lvl>/<Dest>,<ID>,2
Disable LOCK.
@[sp]W:<Lvl>/<Dest>,<ID>,0
6 @[sp]z:<Lvls>
7 @[sp]K?<SorD><AorK>,<Ofset>
Function
S:<Lvl><Dest>,<Src>
S:<Lvl><Dest>,<Src>
S:<Lvl><Dest>,<Src>
C:<Lvls>/<Dest>,<Src>[.....[S<Salvo number>][L<Link
number>]]:I<ID>
V:<Lvl><Dest>,<Src>
V:<Lvl><Dest>,<Src>
S:<Lvl><Dest>,<Src>
C:<Lvls>/<Dest>,<Src>[.....[S<Salvo number>][L<Link
number>]]:I<ID>
W!<Lvl><Dest>,<ID>,1
W!<Lvl><Dest>,<ID>,2
W!<Lvl><Dest>,<ID>,0
S:<Lvl><Dest>,<Src>
C:<Lvls>/<Dest>,<Src>[.....[S<Number of crosspoints
in Salvo>][L<Number of Links>]]:I<ID>
K:<SorD><AorK><No.>,<Dat>
Serial LAN *1
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
－
Yes
－
Yes
－
Yes
－
Yes
Yes Yes
- Yes
Command response
35
Protocol *2
Crosspoint remote control /
Crosspoint remote control 2
Crosspoint remote control 2
Crosspoint remote control /
Crosspoint remote control 2
Crosspoint remote control 2
Ref.
－
－
－
－
－
－
－
－
－
4-3-3