Hitachi NES1-004SB Quick Reference Manual page 294

Index
H
H terminal ........................................................... 5-5
heat sink overheat warning ............................... 7-72
heat sink temperature monitoring ....................... 7-3
HLD .................................................................. 7-27
hold down .................................................. 6-5, 6-10
I
Initial screen selection ...................................... 7-46
initialization ....................................................... 7-77
initializes all Parameters ................................... 7-77
input power display ............................................. 7-3
input terminal a/b selection ............................... 7-12
input terminal response time............................. 7-13
inspection .................................................. 2-1, 11-1
instantaneous power failure/
under-voltage trip alarm enable .................. 7-52
intelligent input terminal ............................. 5-6, 7-12
intelligent input terminal status ........................... 7-2
intelligent output terminal ........................... 5-6, 7-13
intelligent output terminal status ......................... 7-2
intelligent relay output terminal .................. 5-6, 7-14
internal DC braking ........................................... 7-43
inverted-U-curve acceleration /
deceleration ................................................ 7-30
IRDY ................................................................. 7-73
J
JG ..................................................................... 7-25
jogging command setting .................................. 7-25
jump frequency function ................................... 7-26
K
KHC .................................................................... 7-3
L
L terminal ............................................................ 5-5
LAD .................................................................. 7-19
LOC .................................................................. 7-73
LOG1 ................................................................ 7-71
logical output signal operation .......................... 7-71
low-current indication signal ............................. 7-73
M
main circuit terminal ............................................ 5-5
maintenance and inspection ............................. 11-1
major failure signal ........................................... 7-74
maximum frequency ......................................... 7-11
manual torque boost ......................................... 7-22
megger testing .................................................. 11-3
modbus RTU ...................................................... 8-1
MJA .................................................................. 7-74
multispeed select setting .................................. 7-28
multistage speed determination time ................ 7-28
N
NDc .................................................................. 7-72
NO/NC ..................................................... 7-12, 7-14
number of retry on over voltage / over
current trip .................................................. 7-51
O
O/OI terminal ............................................. 5-5, 7-16
OD .................................................................... 7-37
OHF ................................................................. 7-72
OL ................................................................... 7-63
OLR .................................................................. 7-63
operation time over signal
(RNT)/plug-in time over signal
(ONT) ......................................................... 7-70
OPE ................................................................. 7-45
operator selection for frequency
operation .................................................... 7-31
output active state ............................................ 7-14
output current monitoring ................................... 7-1
output frequency monitoring ............................... 7-1
output frequency setting ..................................... 7-6
output on delay ................................................. 7-15
output off delay ................................................. 7-15
output voltage monitoring ................................... 7-3
overcurrent restraint ......................................... 7-64
overload notice advance signal ........................ 7-64
overload restriction ........................................... 7-63
P
P24 terminal ..................................... 5-5, 5-12, 5-13
PID function...................................................... 7-34
PID feedback monitoring .................................... 7-1
PIDC ................................................................ 7-37
PID rariation range ........................................... 7-34
PID scale ................................................... 7-1, 7-35
PID sleep function ................................... 7-34, 7-38
PLC terminal ................................... 5-5, 5-12, 5-13
power-on time over .......................................... 7-70
PRG lamp .......................................................... 6-5
program lamp ..................................................... 6-5
programmable controller .................................. 5-14
PWR lamp ................................................... 6-4, 6-5
R
reduced-torque characteristic
(electronic thermal) ..................................... 7-61
reduced torque characteristic (VP) ................... 7-20
reduced voltage start ........................................ 7-24
REF .................................................................. 7-76
reset ........................................................ 6-19, 7-55
restart frequency threshold ............................... 7-51
restart mode on power failure /
under-voltage trip ........................................ 7-51
restart with an active matching
frequency .................................................... 7-54
retry of OV/OC ................................................. 7-51
retry wait time before motor restart .................. 7-51
reverse rotation signal ...................................... 7-74
reverse PID action ............................................ 7-34
RNT .................................................................. 7-70
ROK ................................................................. 7-27
rotation direction minitoring ................................ 7-1
rotational direction restriction ............................. 7-7
RS ........................................................... 6-19, 7-55
RUN ................................................................. 7-68
RUN key ............................................................. 6-5
RUN LED ........................................................... 6-5
running time over ............................................. 7-70
Index - 2