Related Manuals for Extron electronics XTP T USW 103 4K
Summary of Contents for Extron electronics XTP T USW 103 4K
- Page 1 User Guide XTP Systems XTP T USW 103 4K Three Input Switcher with an Integrated XTP Transmitter 68-2754-01 Rev. A 05 17...
-
Page 2: Safety Instructions
Safety Instructions Safety Instructions • English Istruzioni di sicurezza • Italiano AVVISO: Il simbolo, , se usato sul prodotto, serve ad avvertire l’utente WARNING: This symbol, , when used on the product, is intended to della presenza di tensione non isolata pericolosa all’interno del contenitore alert the user of the presence of uninsulated dangerous voltage within the del prodotto che può... - Page 3 ついては、 エクス トロンのウェブサイ ト より 『Extron Safety www.extron.com and Regulatory Compliance Guide』 (P/N 68-290-01) をご覧ください。 Copyright © 2017 Extron Electronics. All rights reserved. Trademarks All trademarks mentioned in this guide are the properties of their respective owners. The following registered trademarks( ®...
- Page 4 FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
-
Page 5: Conventions Used In This Guide
Conventions Used in this Guide Notifications The following notifications are used in this guide: Potential risk of severe injury or death. WARNING: AVERTISSEMENT : Risque potentiel de blessure grave ou de mort. ATTENTION: • Risk of property damage. • Risque de dommages matériels. NOTE: A note draws attention to important information. -
Page 7: Table Of Contents
Front Panel Operation ........17 Furniture Mounting......... 42 Switch Modes..........17 Rack Mounting ..........42 Front Panel Lockout Mode Firmware Download ........... 43 (Executive Mode) .......... 17 EDID ..............18 Reset Mode ............18 XTP T USW 103 4K Switcher • Contents... - Page 8 XTP T USW 103 4K Switcher • Contents viii...
-
Page 9: Introduction
4K. The XTP T USW 103 4K works with XTP Systems for signal distribution and long-distance transmission between XTP devices. The following diagram shows one way the XTP T USW 103 4K can be integrated in an XTP point-to-point application. -
Page 10: System Compatibility
System Compatibility The XTP T USW 103 4K is compatible with XTP systems, but the maximum video resolution may be limited with different XTP devices. See the table below for maximum video resolutions and refresh rates for various XTP systems. -
Page 11: Video Features
ASCII commands that allow for quick and easy programming. • Contact closure remote control with tally output — Can be used for external control of input switching. XTP T USW 103 4K Switcher • Introduction... -
Page 12: General Features
1U high, half rack width metal enclosure • Highly reliable, energy-efficient external universal power supply included — Provides worldwide power compatibility, with high demonstrated reliability and low power consumption for reduced operating costs. XTP T USW 103 4K Switcher • Introduction... -
Page 13: Installation
Installation This section contains installation procedures for the XTP T USW 103 4K and wiring details. Topics in this section include the following: • Rear Panel Connectors • Connection Details Rear Panel Connectors CONTACT TALLY OUT RS-232 XTP T USW 103 4K... -
Page 14: Inputs And Output Connections
— Connect a digital video source device to the female DisplayPort connector, labeled input 3. HDMI output connector — Connect a digital video display to the HDMI output connector for a local display of the selected input. XTP T USW 103 4K Switcher • Installation... -
Page 15: Xtp Interconnection
System communication • Signal Link Signal LED indicator — Lights green when the XTP T USW 103 4K outputs a video signal or a test pattern. Link LED indicator — Lights yellow when XTP devices are connected and communication is established. -
Page 16: Control Connections
— Connect the external 12 V, 1.5 A power supply to the 2-pole captive screw connector (see Power Connection on page 14). NOTE: The XTP T USW 103 4K requires a local power supply and does not support XTP remote power. XTP T USW 103 4K Switcher • Installation... -
Page 17: Connection Details
Red return Red return Red return Green return Green return Green return Blue return Blue return Blue return Ground Ground Ground EDID/DDC EDID/DDC EDID/DDC H sync Csync V sync EDID/DDC return EDID/DDC return XTP T USW 103 4K Switcher • Installation... -
Page 18: Hdmi Connection
( ATTENTION: • Connect and pull the tie wraps until they are secure. Do not overtighten. • Connectez et tirez les serre-câbles jusqu’à ce qu’ils soient sécurisés. Ne pas trop serrer. XTP T USW 103 4K Switcher • Installation... -
Page 19: Supported Cables
Connector Figure 7. Twisted Pair Cable Termination Supported cables The XTP T USW 103 4K is compatible with shielded twisted pair (F/UTP, SF/UTP, and S/FTP) and unshielded twisted pair (U/UTP) cables. ATTENTION: • Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201 cable to link the XTP products. -
Page 20: Twisted Pair Cable Termination For Pass-Through Ethernet Communication
Blue Blue Blue Side View Insert Twisted White-blue White-blue White-blue White-blue Pair Wires Green Green Orange Green RJ-45 Connector White-brown White-brown White-brown White-brown Brown Brown Brown brown Figure 8. RJ-45 Pin Assignment XTP T USW 103 4K Switcher • Installation... -
Page 21: Rs-232 And Ir Over Xtp Communication
Do not tin the wires. Tinned wire does not hold its shape and can become loose over time. • Ne pas étamer les câbles. Les câbles étamés ne sont pas aussi bien fixés dans les terminaisons des connecteurs à vis captives et pourraient sortir. XTP T USW 103 4K Switcher • Installation... -
Page 22: Power Connection
Connector Tie Wrap SECTION A–A 3/16” (5 mm) Max. Smooth Ridges Power Supply Output Cord Figure 10. Power Wiring See the notifications on the next page for local power information and considerations. XTP T USW 103 4K Switcher • Installation... - Page 23 La longueur idéale est de 5 mm (3/16 inch). Do not tin the stripped power supply leads. Tinned wires are not as secure in the TIP: captive screw connectors and could be pulled out. XTP T USW 103 4K Switcher • Installation...
-
Page 24: Operation
Hotline. See the contact numbers on the last page of this guide for the nearest Extron office. This section contains information for front panel operation and configuration of the XTP T USW 103 4K. Topics in this section include: •... -
Page 25: Front Panel Operation
19), the XTP Configuration Software (see Configuration Software on page 27), or sometimes contact closure. Switch Modes The XTP T USW 103 4K operates in one of the following input switch modes: Auto switch mode — Automatically switches inputs based on availability. • •... -
Page 26: Edid
EDID To manage EDID on the XTP T USW 103 4K, use the XTP System Configuration Software (see EDID Minder on page 40). The XTP T USW 103 4K can record and save EDID in a user memory location, select a pre-defined EDID, or use EDID from a display connected to a receiver. -
Page 27: Sis Configuration And Control
SIS commands consist of one or more characters per field. No special characters are required to begin or end a command sequence. When the XTP T USW 103 4K determines that a command is valid, it executes the command and sends a response to the host device. All... -
Page 28: Error Responses
Error Responses When the XTP T USW 103 4K receives an SIS command and determines that it is valid, it performs the command and sends the corresponding response to the host device. If the command is determined invalid or contains invalid parameters, the receiver returns an error response to the host. -
Page 29: Command And Response Tables For Sis Commands
1 dB steps ( = default) = Audio gain in 1 dB steps ( = default) = Audio attenuation to + in 1 dB steps ( = default) = Audio level XTP T USW 103 4K Switcher • SIS Configuration and Control... -
Page 30: Picture Adjustment Commands (Analog Only)
= Black video signal resolution = 720p @ 60 Hz (default) = 1080p @ 60 Hz = Default) = Picture adjustment = Default) 65535 32768 = Horizontal or vertical shift XTP T USW 103 4K Switcher • SIS Configuration and Control... -
Page 31: Preset Commands
EDID from a display connected to the local HDMI output EDID from a display connected to a receiver output User assigned User assigned User assigned * = default per video format XTP T USW 103 4K Switcher • SIS Configuration and Control... -
Page 32: Advanced Configuration Commands
Pressing the button a third time unmutes the input audio and video. • If audio and video are already muted upon input selection, pressing the button a second time unmutes the input audio and video. XTP T USW 103 4K Switcher • SIS Configuration and Control... - Page 33 = input reports as an HDCP authorized device (default) = disabled (default) = Test pattern = 720p @ 50 Hz = 720p @ 60 Hz = 1080p @ 60 Hz XTP T USW 103 4K Switcher • SIS Configuration and Control...
- Page 34 = Device name = no input detected = Input signal presence = input detected = no source detected = HDCP status = source is HDCP-compliant = source is not HDCP-compliant XTP T USW 103 4K Switcher • SIS Configuration and Control...
-
Page 35: Configuration Software
Software This section contains installation and configuration procedures for the XTP System Configuration Software to directly configure and control the XTP T USW 103 4K. The switcher can also be configured and controlled remotely through the XTP System Configuration Software and the XTP matrix switcher (see the XTP System Configuration Software Help file). - Page 36 Submit any required information to start the download. Note where the file is saved. Open the saved executable (.exe) file. Follow the instructions that appear on the screen to install the program. XTP T USW 103 4K Switcher • XTP System Configuration Software...
-
Page 37: Software Product Page
Submit any required information to start the download. Note where the file is saved. Open the saved executable (.exe) file. Follow the instructions that appear on the screen to install the program. XTP T USW 103 4K Switcher • XTP System Configuration Software... -
Page 38: Software Connection
Software Connection To connect the software directly to the XTP T USW 103 4K, connect the computer running the software to the front panel configuration port (see figure on page 16). Figure 16. Connections Screen To connect to a device: Open the XTP System Configuration Software. -
Page 39: Software Operation
Backup and Restore Commissioning Report available when the computer is directly connected to the device. See an XTP matrix switcher user guide (www.extron.com) for more information on these features. XTP T USW 103 4K Switcher • XTP System Configuration Software... -
Page 40: Update Firmware
This option resets all disabled confirmation dialogs to the default settings. From the menu, select . The Tools Software Preference Software Preference dialog box opens. Figure 21. Software Preference Dialog Box Click the button. The dialog box closes. Reset XTP T USW 103 4K Switcher • XTP System Configuration Software... - Page 41 This option opens the XTP System Configuration Software help file in a Web browser. From the menu, select Help Help Extron Website This option opens the Extron website in a Web browser. From the menu, select Help Extron Website XTP T USW 103 4K Switcher • XTP System Configuration Software...
-
Page 42: Device Settings
AV Mute buttons — mute or unmute both the video and audio. • NOTE: If video or audio is muted on the local HDMI or XTP output, and a new input is selected, the video or audio remains muted. XTP T USW 103 4K Switcher • XTP System Configuration Software... - Page 43 For source devices that encrypt their output even if the source material does not • require HDCP encryption, disable the HDCP Authorized feature to view the content on non-HDCP compliant displays. XTP T USW 103 4K Switcher • XTP System Configuration Software...
- Page 44 Save Preset — To save a preset, select one from the list of presets and click the Save button. Preset Recall Preset — To recall a saved preset, select the desired preset from the list of presets and click the button. Recall Preset XTP T USW 103 4K Switcher • XTP System Configuration Software...
- Page 45 Allow Audio Only to be output. When enabled, select the desired resolution and refresh rate from the drop-down list to emulate in place of video. Signal Type XTP T USW 103 4K Switcher • XTP System Configuration Software...
-
Page 46: General Tab
(the tally output LED mode also remains unchanged). In this case, pressing the button a second time unmutes the video and audio. XTP T USW 103 4K Switcher • XTP System Configuration Software... - Page 47 Selected Audio Input — Displays the type of the currently selected audio input. Audio only — Displays the status of the checkbox. Allow Audio Only Analog Audio Gain — Displays the analog audio gain in dB. XTP T USW 103 4K Switcher • XTP System Configuration Software...
-
Page 48: Edid Minder
To assign EDID to all inputs: Select an available EDID icon from the , or Favorites Connected Outputs Available panel ( EDID Click the button ( Assign to All XTP T USW 103 4K Switcher • XTP System Configuration Software... - Page 49 Common Timings Connected Outputs listing the EDID settings common among the selected outputs. Select the desired common EDID. The EDID is shown in the panel. Available EDID XTP T USW 103 4K Switcher • XTP System Configuration Software...
-
Page 50: Reference Information
• Firmware Download Mounting The XTP T USW 103 4K can be placed on a tabletop or mounted in a rack or underneath a desk. Tabletop Mounting Attach the provided rubber feet to the bottom four corners of the enclosure. -
Page 51: Firmware Download
Click the link ( ) to the right of the desired product. Download Submit any required information to start the download. Note where the file is saved. XTP T USW 103 4K Switcher • Reference Information... -
Page 52: Extron Warranty
Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.