Table of Contents
Advertisement
Nose Gear Assembly and Installation
Nose landing gear accessories list:
A-Electric retract
B - E-clips
(02.0 pcs)
C - Nose gear steering push rod
D - Nose gear steering control collar
E - Trunion
F - Nose gear metal pin
G - Steering tiller
H - Nose gear main strut
I - Grubscrew
(M4*4 2pcs)
J - Screw
(PM2•4 1 pcs)
K- Screw
(PM2•3 1 pcs)
L - LI-shaped collar
M- Pins
(2pcs)
1.
At first, insert the "Nose gear metal pin (F)"
into the "Trunion(E)", and clip the "E-clip(B)" to the
"Nose landing gear metal wire (F)" to lock it in
place.
2.
Put the "Nose gear steering control collar (D)"
on the "Nose gear steering push rod (C)", slide
the assembly into the hole on the "Steering tiller
(G)"and lock it in place.
3.
Put the installed Steering tiller(G)" on the
"Nose gear metal pin(F)", and secure it with the
screw. Ensure the screw and the flat spot of the
pin are aligned.
4.
Next, put the "Nose gear main strut (H)" onto
the "Nose gear metal pin(F)",and secure it with 2
"Grub screws(I)".
5.
Put the "Spring (N)" in the "Nose gear main
strut (H)",then insert the "Damping pin(R)" into the
"Nose gear main strut (H)", press down on the
"Damping pin(R)", and thread the "screw (J)" in the
"nose landing gear main strut (H)", to lock the
"Damping pin(R)" in place.
6.
Put the "U-shape collar(L)"on the "Nose gear
main strut (H)",and secure it with "Screw (K)".
7.
Use "E-clips(P)" and "Pins(M)" to connect the
"Shaft support lever (Q)", the "8-shaped damping
shaft (O)" and the "U-shape d collar(L)".
8.
lnsert the "wheel shaft (Z)" into the "Shaft
support lever (Q)", and use "Grub screw(S)" to
secure the "Wheel shaft (Z)".
9.
Put the "Spacers(U)" and "Wheels(T)" on the
"wheel shaft (Z)", and use "E-clips(V)" to secure
the two wheels.
10. Place the "Nose gear assembly(Y)" on the
Nose gear mounting point(X)", and secure it with 4
"Screws(W)".
&
Note:
When installing, please check that the flat position of part is
aligned with the screw before tightening. The flat position must face the screw
hole so that it can lock in place properly. Failure to do so can result in the
piece being misaligned, or worse, falling off.
Nose Gear Servo Installation
Accessories list
A-Metal gear servo
B - U-shaped servo arm
C - Screws
(PWA2•8 2pcs)
D - Screw
(PM3.6)
E - Screw
(PWA 1. 7'5)
F - Pushrod
G - Landing gear steering collar
1.Use a servo tester or radio to center the servo.
2.Use "screws(C)" to secure the "Servo(A)". Install the "U-shaped
servo arm(B)" on the servo and secure it with "Screw(E)".
3.Snap the clevis of "Push rod(F)" into the "Landing gear steering
collar(G)" and insert the other end into the "U-shape servo arm (B)".
Center the nose wheel.
4.Use "Screw(D)" to secure the "Pushrod(F)".
r=
75 mm
(2.95 in)
F/A 18E Super Hornet
Item No.: FJ3021
Version No.: FJ3021-V02
N - Spring
0 - 8-shaped damping shaft
P -
E-Clips(01.5 2pcs)
Q - Shaft support lever
R - Damping pin
S -Grub screw
T-Wheel
U - Spacer
V- E-clips
(02.0
2pcs)
Z - Wheel shaft
W -Screws
(PA3•45 4pcs)
X - Nose gear mounting point
Y - Nose gear assembly
•I
Pushrod diameter : 0 1.2mm
V1
R
,
��
N
..
p--
_____,_,
•
�
�
- -
L
0 i
'
�
��
H
J___..---
c:@��
-5-
c:=:w-M1
M
□
:@Ih
Rotating p�shrod,
ca:
increa':
or reduce control distance.
EN
Advertisement
Table of Contents
