Related Manuals for Freewing F-16 FIGHTING FALCON V3
Summary of Contents for Freewing F-16 FIGHTING FALCON V3
- Page 1 F-16 FIGHTING FALCON V3 USER MANUAL Wingspan: 878mm Iten No.: FJ211 Version No.: FJ211-V02 www.sz-freewing.com MADE IN CHINA...
- Page 2 30 countries to this day, the F-16 has distinguished its place in aviation history. Freewing has modeled this brilliant aircraft in EPO foam with a 70mm electric ducted fan (EDF) powerplant. With a 1 3 0 6 mm length and 878mm wingspan, this 1/12 scale flying replica includes many exciting features! An accurate scale outline with sharp surface details and panel lines make this model stand out at your airfield.
-
Page 3: Packing List
Pre-installed all No electronic Pre-installed Main wing Pushrod electronic parts equipment servo No electronic Pre-installed all Pre-installed Vertical tail Carbon tube electronic parts equipment servo Horizontal tail Glue/Decals Nose cone、FIn Manual F-16 Fighting Falcon Iten No.: FJ211 Version No.: FJ211-V02 www.freewing-model.com... - Page 4 3 .Use 4pcs screws to fix the main wing. Screw（KA3x10 4pcs） Install Fuselage 平 尾 组 装 1.Use glue to attach the left/right tail fuselage pieces onto the fuselage. F-16 Fighting Falcon Iten No.: FJ211 Version No.: FJ211-V02 www.freewing-model.com...
- Page 5 1. Connect the rudder servo wire and fuselage extension wire. 2. Install the vertical tail on the fuselage and fix it with screws S cre w （K A 3 x1 0 m m 4 p cs) F-16 Fighting Falcon Iten No.: FJ211 Version No.: FJ211-V02 www.freewing-model.com...
- Page 6 Aileron pushrod mounting hole Pushrod diameter Ø1.2mm 55mm Elevator pushrod size Elevator pushrod mounting hole Pushrod diameter Ø1.5mm 78mm Rudder pushrod mounting hole Rudder pushrod size Pushrod diameter Ø1.2mm 53mm F-16 Fighting Falcon Iten No.: FJ211 Version No.: FJ211-V02 www.freewing-model.com...
- Page 7 Landing gear Installation Instructions Install nose landing gear Please refer to the following photo，assemble、replace、revise the nose landing gear sparepart name and parameters (M3x3 1pcs) H- Nose gear steering rod N- Screw (KA2.6x12 4pcs) A- Jimi screws O- Nose gear screw fixed part I - Metal shaft B- Wheel chock P - Nose gear installed set...
-
Page 8: Servo Parameters
100mm Left aileron 9g Digit-Hybrid Standard 200mm Right aileron 9g Digit-Hybrid Standard 200mm Left elevator 9g Digit-Hybrid Standard 900mm Right aileron 9g Digit-Hybrid Reverse 900mm Rudder 9g Digit-Hybrid Standard 200mm F-16 Fighting Falcon Iten No.: FJ211 Version No.: FJ211-V02 www.freewing-model.com... -
Page 9: Control Board Instruction
Landing gear board. Rudder The control surface is not any note on Elevator the control board, connect directly to Aileron (power to the receiver) the receiver. Motor parameters 29571 F-16 Fighting Falcon Iten No.: FJ211 Version No.: FJ211-V02 www.freewing-model.com... - Page 10 I n s t a l l b a t t e r y battery compartment cover Installed the battery and use velcro to fix. battery Pull the sticker back and open the cockpit. Velcro battery tray Battery cabin space size:L=260 W=70 H=45(mm) Before connect the battery and receiver, please The battery capacity and discharge rate switch on the transmitter power and make sure the...
-
Page 11: Control Direction Test
After installed the plane, before flying, we need a fully charged battery and connect to the ESC, then use radio to test and check that every control surface work properly. Aileron Stick Left Stick Right Elevator Up Elevator Down Elevator Rudder Stick Left Stick Right F-16 Fighting Falcon Iten No.: FJ211 Version No.: FJ211-V02 www.freewing-model.com... - Page 12 H1/H2 30mm/30mm Low Rate D/R Rate: 65% D/R Rate: 80% D/R Rate: 85% H1/H2 34mm/34mm H1/H2 34mm/34mm H1/H2 35mm/35mm High Rate D/R Rate: 100% D/R Rate: 100% D/R Rate: 100% F-16 Fighting Falcon Iten No.: FJ211 Version No.: FJ211-V02 www.freewing-model.com...