Table of Contents
Advertisement
Nose Gear Assembly and Installation
A- Landing gear electric retract
B- E-clip (02.0mm pcs)
C- Nose gear steering pushrod
D- Nose gear steering control ring
E- Landing gear trunion
F- Attachment Pin
G- Steering tiller
H- Nose gear strut
I- Grub screw
(M4*4mm 2pcs)
J- Screw
(PM2*4mm 1 pc)
K- Screw
(PM2*3mm 1 pc)
L- Dampening arm collar
M- E-clip
(01.5mm 3pcs)
N- Spring
O- "8" shaped dampening arm
P- Pin
(2 pcs)
Q- Pin
R- Piston/lower strut
S- Wheel strut
T- Wheel
U- Wheel shaft
V- Assembled nose gear set
W-Gear mount hard point
X- Screws
(PWA3*12mm 4 pcs)
1.Start by inserting the "Nose gear attachment pin(F)" into
the "Landing gear Trunion (E)", and snap the "E-clip(B)" to
the "Nose gear Attachment Pin (F)" to secure it
2.Put the "Nose gear steering control ring (D)" in the"Nose
gear steering pushrod (C)", thread a screw to the side of the
"Steering tiller (G)"to secure the "Nose gear steering
pushrod (C) in place.
3.Place the assembled "Steering tiller (G) onto the "Landing
gear attachment pin (F) and secure it with a screw.
4.Next, place the "Nose gear strut (H)" onto the "Nose gear
attachment pin (F)" and secure it using 2 "Grub screws (I)".
5.Put the "Spring (N)" in the "Nose gear strut (H)", then insert
the "Piston/lower strut (R)" into the "Nose gear strut )H)".
Press down on the "Piston/lower strut (R)"and lock it in
place using "Screw (J)" through the "Nose gear strut (H)".
6.Place the "Dampening arm collar (L)"on the "Nose gear
strut (H)" and secure it with "Screw (K)".
7.Use "Pin (P)" and "E clip (M)" to secure the "Wheel strut
(S)" to the "Piston/lower strut (R)", then use the "8 shaped
dampening arm (O)" , "Pin (P)" and "E-clip (M)" to connect
the "Wheel strut (S)"to the "Dampening arm collar (L)".
8.Use "Wheel shaft (U)"and E-clip (B)" to attach the "Wheel
(T)" to the "Wheel strut (S)".
9.Place the "Assembled nose gear set (V)"onto the "Gear
mount hard point (W)"and secure it with 4 "screws (X)".
Steering Servo Installation
Accessories List
A- 9g servo
B- Screws
(PWA2*8mm 2 pcs)
C- Screw
(PM2*4mm)
D- Screw
(PM3*6mm)
E- Servo arm
F- Pushrod
G- Nose gear steering control ring
1. Place the "Servo (A)" onto the wooden deck, use
"Screws (B)" to secure it.
2. Install the "Servo arm (E)"on the "Servo (A)" and use
"Screw (C) to secure it.
3. Snap the clevis of the "Pushrod (F)"to the "Nose gear
steering control ring (G)"and insert the other end
through the eye of the "Servo arm (E)", then center
the nose wheel.
4. Use "Screw (D)" to lock the pushrod to the servo
control arm.
Super Scorpion
Item No.: FJ207
Version No.: FJ207-V01
V
yv
Note:
When installing, please check the flat position of the part when locking the grub screw
down. The flat position must face the Grub screw in order for it to lock . Ensure this is done
properly, the part may come off if it isn't locked
,... r::
___ 65 mm
,__
(2.55 in)
-6-
T
y---B1
--s
---�M1
0
N
H
•I
Pushrod diameter : 0 1.2mm
�=· !;;;,
.a1•--·=
□
EN
[§[)½
Advertisement
Table of Contents
