Nose Gear Assembly And Installation - Freewing A-6E Intruder User Manual

Nose Gear Assembly and Installation (4s and 6s Versions)
The A-6 comes in two versions, the 4s standard version and a 6s upgraded version. The 4s version utilizes a basic wire type landing gear
whereas the 6s upgraded version comes with a spring loaded aluminum shock absorbing style landing gear. The upgraded landing gear is
also available to purchase separately if you choose to upgrade your 4s system.
A - Electric retract
B - E-clip (O2.0mm)
C - Trunnion
D - Metal pin
E - Screw (PT2.6x6mm)
F - Nose gear upper strut
G - U-shaped damping collar
H - Spring
I - Shaft
J - Landing gear steering pin
K - Pushrod collar
L - Steering tiller
M - Grub screws (M4x3mm 2pcs)
N - Screw (PM2x4mm)
O - Screw (PM2x3mm)
P - Lower strut
Q - Dampening shaft
R - Grub screw (M3x3mm)
S - Nose wheel axle
T - Wheels ( O 35x10mm)
U - E clip (O1.5mm)
V - Pin
W - Landing gear assembly
X - Screws (PA2.6x10mm)
Y - Nose gear hard point
1. Disassemble the "Electric retract(A)", and remove
the trunnion.
2. Insert the "Metal pin(D)"into the "Trunnion(C)" and
secure it with "E clip(B)".
3. Put the "Pushrod collar(K)"onto the end of the
"Landing gear steering pin(J)"and thread it into the
"Steering tiller(L)".
4. Put the "Steering tiller(L)" and the "Nose gear main
strut(F)"on the "Metal pin(D)" and use 2 "Grub
screws((M)" and Grub screw(E)" to secure the
assembly.
5. Put the "U shaped dampening collar(G)" on the end
of the "Nose gear main strut(F)"and secure it with
"Screw(O)".
6. Insert "Spring(H)" and "Shaft(I)" into the the "Nose
gear main strut(F)" and press the "Shaft(I)" down.
Thread the "Screw(N)"into the hole in the side of the
"Nose gear upper strut(F)" to lock the "Shaft(I)" in
place.
7. Use "Pin(V)" and "E clip(U) to connect the "Lower
strut(P)" and the "Dampening shaft(Q)" to the "U
shaped dampening collar(G)".
8. Put the "Wheel(T1)"on the "Nose wheel axle(S)" then
insert the "Nose wheel axle(S)"into the "Lower
strut(P)" and use "Grub screws(R)" to secure the
"Nose wheel axle(S)" to the "Lower strut(P)".
9. Slide the "Wheel(T2)"onto the open end of "Nose
wheel axle(S)" and secure it using "E clip(B)".
10. Place the "Landing gear assembly(W)" onto the
"Nose gear hard point(Y)" and secure it using
"Screws(X)."
Nose Landing Gear List
A- Electric retract
B - E-clips (02.0mm)
C - Trunnion
D - Nose gear strut
E - Nose gear steering pin
F - Pushrod collar
G - Steering tiller
H -Wheel mount
1.Disassemble the "Electric retract(A)", and remove the
"Trunnion(C)".
2.Put the"Pushrod collar(F)" into the" Nose gear steering pin(E)"
and thread it into the "Steering tiller(G)"
3.Put the "Steering tiller(G)" onto the "Nose gear strut (D)", and
use "Screw(O)" to secure it.
4.lnsert the "Nose gear strut(D)" into "Trunnion(C)", and use "E-
clip(B)" to secure it.
5.Put the "Wheel mount (H)" into the end of the"Nose gear strut
(D)", and use the "Grub screws(K)" to secure it.
6.Put the "Wheel(J1 )" on the" Nose wheel axle(I)", then insert the
"Nose wheel axle(I)" into the "Wheel mount(H)", use "Grub screw
(K1 )" to secure it. Then put the other wheel on the "Nose wheel
axle(I)", and secure it with the "E-clip (B2)".
7 .Reassemble the "Electric retract(A)".
8.Place the"Assembled nose gear(L)" onto the "Nose gear hard
point(N)"and use the "4 screws(M)" to secure the unit.
A-BE Intruder
No.:
Item FJ2041
Version No.: FJ2041-VD1
/
a
/
N
Full aluminium damping landing gear instructions
4S standard version metal landing gear (no damping) instructions
I - Nose wheel axle J
-Wheel (035'10mm)
K- Grub screws (M3x3mm)
L- Assembled nose gear set
M- Screws (PA2.6x10mm)
N- Nose landing gear mount
O- Screw (PT2.6x6mm)
-6-
oJ)··
F
Lrl.
Note:
the flat position of the part aligns with the
screw hole, this will lock the piece in place.
Failure to do so could result in the piece
coming off during flight.
Q
When assembling, ensure that