Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Freewing FJ3021
Summary of Contents for Freewing FJ3021
- Page 1 F/A 18E SUPER HORMET...
- Page 2 Before beginning assembly, please read through the instructions and carefully follow them throughout the build. 3. Freewing and it's vendors will not be held responsible for any losses due to improper assembly and operation. 4. Model airplane operators must be at least 14 years of age.
-
Page 3: Table Of Contents
Index Main wing installation Nose gear door installation Vertical stabilizers installation Servo introduction Elevator servo installation Battery installation Elevator installation Center of gravity Nose cone installation Power system assembly Vector servos installation and installation Nose Gear Assembly Motor parameters and installation Vector mix setup Nose gear servo installation Control direction test... -
Page 4: Main Wing Installation
1.Apply the glue to the indicated places as shown in the photo at the right . Attach the vertical stabilizers to the fuselage and allow the glue to dry. Glue (Both sides) F/A 18E Super Hornet Item No.: FJ3021 Version No.: FJ3021-V02... -
Page 5: Elevator Servo Installation
(B) through the -�, hole of control horn( D ) , and lock it with nut (C). FM�•10 Nose Cone Installation 1.Use glue to attach the nose cone to the fuselage. F/A 18E Super Hornet Item No.: FJ3021 Version No.: FJ3021-V02... -
Page 6: Vector Servos Installation
Pushrod diameter: 0 1.2mm (3.4 in) r>r:::= , Installing hole of Vector push rod (Horizontally) Vector pushrod length (Horizontally) Pushrod diameter : 0 1.2mm ===9 2 m= m ===- (3.62 in) F/A 18E Super Hornet Item No.: FJ3021 Version No.: FJ3021-V02... -
Page 7: Nose Gear Assembly And Installation
Center the nose wheel. □ 4.Use "Screw(D)" to secure the "Pushrod(F)". •I :@Ih Pushrod diameter : 0 1.2mm c:@�� 75 mm Rotating p�shrod, increa': (2.95 in) or reduce control distance. F/A 18E Super Hornet Item No.: FJ3021 Version No.: FJ3021-V02... -
Page 8: Main Landing Gear Assembly And Installation
3. Allow at least 2 hours for the glue to dry. 4. After the glue has dried, install the guided missiles as indicated. -..• L ..F/A 18E Super Hornet Item No.: FJ3021 Version No.: FJ3021-V02... -
Page 9: Nose Gear Door Installation
Vector servo (Horizontally) L:100mm Flap servo Positive Reverse Flap servo L:150mm Vector servo (Horizontally) L:100mm Reverse Reverse Aileron servo L:300mm Vector servo (vertically) Reverse L:100mm Positive Aileron servo L:300mm Positive F/A 18E Super Hornet Item No.: FJ3021 Version No.: FJ3021-V02... -
Page 10: Battery Installation
If you find that moving the battery is insufficient, you can use some other suitable material such as a sticky back weight strip to counter weight. 70-75mm (2.76~2.95 in) F/A 18E Super Hornet Item No.: FJ3021 Version No.: FJ3021-V02... -
Page 11: Power System Assembly And Installation
Current Pull Weight Volate Motor No Load Propeller Item No. KV Value Resistance Current 90mm �95A MO037481 22.2 0.020 3600 2.7A/10V 1450RPM/V Ducted Fan F/A 18E Super Hornet Item No.: FJ3021 Version No.: FJ3021-V02... -
Page 12: Vector Mix Setup
5. Enter into the PROG. MIX from radio menu, set the mix for 8CH to elevator and aileron. Vector-Elevator mix Stick Forward Stick Back Vector-Aileron mix Stick Right Stick Left • Vector-Rudder mix Stick Right Stick Left F/A 18E Super Hornet -10- Item No.: FJ3021 Version No.: FJ3021-V02... -
Page 13: Control Direction Test
Engage the kill switch if one is assigned. Install a fully charged battery and connect it to the ESC. Using the radio, ensure that all control surfaces move in the correct direction. Ailerons Stick Right Stick Left Elevator Stick Back Stick Forward Rudder Stick Left Stick Right Optional Flaps Flaps Down F/A 18E Super Hornet -11- Item No.: FJ3021 Version No.: FJ3021-V02... -
Page 14: Dual Rates
H1/H2 25mm/25mm H1/H2 19mm/19mm H1/H2 33mm/33mm Vector center diagram White checking line of vector (Horizontally) White checking line of :- - - - - - - 1 vector (Vetlcally) F/A 18E Super Hornet -12- Item No.: FJ3021 Version No.: FJ3021-V02... -
Page 15: Full Elevator Centering Diagram
D) High speed will happen slightly vibrate D) Its normal to use Control surfaces move in the wrong A) Servo direction is reversed A) Adjust servo reversing function direction -13- F/A 18E Super Hornet Item No.: FJ3021 Version No.: FJ3021-V02... - Page 16 IB-ccuitwg Dongguan Freewing Electronic Technology Ltd HK Freewing Model International Limited Add.:FeiYi Building,face to Labor Bureau, Fu min Middle Road, Dalang Town, Dongguan City , Guangdong Province, China Web: http://www.sz-freewing.com Email:freewing@sz-freewing.com Fax:86-769-82033233 Tel: 86-769-82669669 ffi %ffi" t K � f41i � �& 0 µJ...