Co- presented by SebArt and Freewing, this 90mm EDF jet F104s “ Starfighter” use EPO material, wingspan is 755mm, length is 1720mm. Used two different color schemes, it is the silver color scheme of George Air Force Base, 479th Tactical Fighter Wing FG-907, and the yellow/black color scheme of Italian Air Force 82 anniversary.
Installation Install nose fuselage Install carbon tubes in the trough,and Use glue, Carbon tube to attach the nose and rear fuselage. use glue to attach it. Carbon tube:Ø6x180mm 2pcs Carbon tube:Ø4x100mm 2pcs Note:There is a EPO glue on package,please use it to glue. Glue should be spread evenly, and wait for 90 seconds.Then install on,its best glue condition.
Page 5
Installation Aileron pushrod size Aileron pushrod m ounting hole Pushrod diameter:Ø1.5mm 70mm Servo arm pushrod size pushrod m ounting hole Pushrod diameter:Ø1.5mm 70mm Servo arm Elevator,rudder Install the servo of Elevator/rudder (PWA2x8mm 4pcs) A-Screw B-Servo cover C-Servo box D-Rudder horn E-Rudder pushrod F-Servo cable trough Servo...
Page 6
Installation Tail wing installation Please refer to the following photo to install the tail wing. Step Step Carbon tube Ø4x200mm A-Elevator B-Rudder Step Step A-Horn Screw(FWA3x8 4pcs) B-Elevator pushrod C-Elevator servo Step A-Carbon tube (FA3x8 4pcs) B-Screw Rear fuselage D-Rudder F-104S Starfighter Item No.:FJ310...
Install nose cone Since we use the magnet structure,we only need to attach the nose cone on the nose fuselage. Install air-brake Step Step Step Step 2.Use glue to attach the speed brake set (A) on two side of fuselage. Air-brake set D-Pushrod B-16g Servo...
Install landing gear Nose Landing Gear Assemble Please assemble、disassemble the nose landing gear according to the following photo. Accessories name and specification A-Landing gear electric contvoller Screw(PM2x4mm) E-buckle (Ø1.5mm) B-Nose landing gear steering pushrod K-LED light fixed arm 8-shape connecting arm C-Nose landing gear steering control ring L-U-shape damping arm.
Page 9
Install landing gear Rear Landing Gear Assemble Please assemble、disassemble the rear landing gear according to the following photo. Accessories name and specification Rear gear shock absorber connecting arm Rear gear strut 3 E-buckle Ø1.5mm 8pcs ( ) Rear gear folding strut 2 Wheel Ø60x16mm E-buckle...
Page 10
Install landing gear Rear Landing Gear Assemble Please assemble、disassemble the rear landing gear according to the following photo. Step Screw(PWA3x12 2pcs) Step A-Screw PWA3x8 2pcs PWA3x8 2pcs ( ( ( 4x183.6mm) (Ø4x183.6mm) (Ø4x183.6mm) B-Carbon tube Rear gear mount Fuselage plastic cover F-104S Starfighter Item No.:FJ310...
Install cabin door Install nose/rear cabin door According to the following diagram,assemble/disassemble,replace the nose/rear landing gear cabin door. Install nose cabin door Step Step A-17g servo Servo fixed mount. A-Cabin door rotating shaft Cabin door rotating shaft (PWA2x8mm 2pcs) C- Screw B-Nose cabin door(left/right) Nose cabin door(left/right) C-Cabin door pushrod...
3-Axis Gyro use introduction Use 4pcs screws to fix the gyro on the fix board on the front of Gyro tested before ship, and set up the default sensitivity value. battery compartment. Make sure the gyro decal is forward to the You can do small adjustments according to the actual situation.
Control board use introduction Afterburner access port External UBEC access port Afterburner Throttle (ESC) UBEC cable Flap servo ESC throttle cable FLAP Throttle Air-brake servo FLAP FLAP Air-brake Air-brake Air-brake Air-brake Air-brake LED light(Single flashes) Landing Light Landing Gear Cabin door servo Receiver Gear According to the noted, connect the servo cable or LED light cable to the correct access port.
Notor parameters M3.0 20.35mm 47.29mm M3.0 (4pcs) 54.29mm NOTE:This motor is a special product, only use for Freewing 90mm 12-blade ducted fan P0902, while 90mm 12-blade ducted fan P0902 also cannot install the other motors! Current Volate Pull Motor Weight...
Install power system 1.lnstall the motor(D)”in the“ducted fan housing(C) ” . 2.Fix the motor by 4pcs“cup head screws(B)” . 3.Put the“rotor(E)”in the motor shaft. (During this process,please note the hardware platform of rotor should be alignment with the motor shaft platform) 4.Use“spinner(F)”to cover the rotor,and fix the“spinner(f)”by“cup-head-screw(G)”...
Control direction test After installed the plane,before flying,we need a fully charged battery and connect to the ESC,then use radio to test and check that every control surface work properly. Aileron Stick Right Stick Left Elevator Up Elevator Down Elevator Rudder Stick Left Stick Right...
Dual Rates According to our testing experience,according to the following parameters to set the aileron/elevator rate,it will be useful for flight.ln low rate,its good for flight control and its suitable for the initial flight or less skilled players. According to your own circumstance,choose one rate in flight. Flaps Aileron Elevator...