Table of Contents
Advertisement
P R O G R A M M I N G T H E S Y S T E M
recording of an engine compartment module mode. Connect the module in accordance
with installation manual. The system will confirm the registration with a short sound signal.
Saving changes:
To finish the recording of the engine compartment module,
be pressed once again, the series of red and green flashes of the status
the saving, switch on the ignition to save the settings and exit programming mode.
Level 6, 7 – Recording Bluetooth radio relays No 1, No 2
Radio relays recording is performed one by one starting from the 6 level: radio relay
№1 is recorded on the 6 level; radio relay №2 is recorded on the 7 level. The radio relay
can be overwritten only on the level of its initial registration.
To record Bluetooth radio relays №1, №2, enter programming mode and press
button 6 times for radio relay №1 or 7 times for radio relay №2.
and the system will enter the recording of a radio relay mode. Connect a relay in accordance
with installation manual. The system will confirm recording with a short sound signal.
Saving changes:
To finish the recording of the Bluetooth radio relay,
pressed once again, the series of red and green flashes of the status
will confirm the saving, switch on the ignition to save the settings and exit the
programming mode.
Level 8 – Recording Bluetooth GPS/GLONASS receiver
To record a Bluetooth GPS/GLONASS receiver, enter programming mode and
VALET
LED
press
button 8 times. The
will enter the recording of a receiver. Connect the receiver in accordance with its
installation manual. The system will confirm the registration with a short sound
LED
signal and red light of
indicator.
Saving changes:
To finish the recording of the engine compartment module, press
once, the series of red and green flashes of the status
switch on the ignition to save the settings and exit programming mode.
56
PANDORA DXL 1090L SERVICE-SECURITY SYSTEM
VALET
button should
LED
will confirm
VALET
LED
indicator will light green
VALET
button should be
LED
indicator
indicator will light green and the system
VALET
button
LED
will confirm the saving,
P R O G R A M M I N G T H E S Y S T E M
Level 10 – Configuring system settings via the wireless interface
This function is under construction.
Level 11 – Programming and configuring «Immobilizer code»
To program the «Immobilizer code», enter the programming mode and press
button 11 times. The level is divided into 3 sublevels (Sublevel 11.1 – Selecting buttons;
sublevel 11.2 entering PIN-code; sublevel 11.3 – confirmation of the PIN-code input).
The system will automatically enter the sublevel 11.1 (Selecting buttons) after
entering the level 11. The system can determine buttons via analog «Code immobilizer»
input or via digital protocol of a car. It is necessary to configure an analog input (INP)
as «Code immobilizer» in the settings of the base unit inputs when implementing the
«Code immobilizer» via an analog input. It may be necessary to switch on the ignition
after entering the level 11 of programming (if the car bus is active only when the ignition
is switched on) when implementing the «Code immobilizer» via digital car bus protocol.
After selecting active buttons enter the sublevel 11.2 (Entering PIN-code) by one
VALET
pressing of
button. Program PIN-code using selected buttons at this sublevel;
VALET
press
button once and enter PIN-code again. To confirm PIN-code re-entering
VALET
and save all the settings, press
button once again.
Sublevel 11.1 – Selecting buttons:
This sublevel is used to select active buttons via digital protocol of a car or via «Code
Immobilizer» analog input. To determine the activity of the analog «Code Immobilizer»
input, apply potential to the corresponding input (INP) of the base unit,
will be flashing orange.
If you determine buttons via digital protocol select one or more buttons (up to four)
for entering the secret code of the immobilizer. To do this press the selected button,
LED
indicator will confirm input with orange flashes. If there are no orange flashes
when any button is pressed, then this button is not recognized by the system, select a
different button. Repeat the procedure to select the second, third, fourth button and
enter the next sublevel. To enter the next sublevel press
USER MANUAL
VALET
LED
indicator
VALET
button once.
57
Advertisement
Table of Contents
