Table of Contents
Advertisement
P R O G R A M M I N G T H E S Y S T E M
overwrite new remote controls or record old remote controls again, radio tags will not
be overwrite. All previously recorded radio tags will be removed when you overwrite
new radio tags or record old radio tags again, remote controls will not be overwrite.
Recording remote controls:
• Press three buttons
hold them for 1 second (until a short beep from the main remote control or until
LED
fading of additional remote
), then release the buttons. If the recording was
successful, LCD remote will emit 2 short beeps and the base unit will emit 1 beep,
after that you can move to recording the next remote control or radio tag.
Recording radio tags:
• Press control button on a tag and hold it for 6 seconds (6 flashes of tag status
indicator), release the button after the sixth flash. If the recording was successful, a
siren will emit 1 beep, after that you can move to recording the next tag.
Saving changes:
VALET
To finish the recording, press
button once. The series of red and green flashes
LED
of status
indicator will confirm the saving.
Level 2 – Changing the factory preset of the «Service PIN-code»
Prepare a new value of the «Service PIN-code», it should consist of 4 digits (from 1 to
9). Write down or remember the new PIN-code.
Enter programming menu and then press
enter «Changing Service PIN-code» mode and the status
Changing the «Service PIN-code»:
• Enter the first digit of the code using
times, equals to the first digit. Pauses between presses should not exceed 1 second, every
LED
pressing will confirm with orange
indicator flash. Pause for more than 1 second and
LED
red
indicator confirms the input of the first digit. Then you can enter the next digit.
• Enter the other numbers in the same manner. The input of the fourth number
will be confirmed by series of red and green
wait for PIN-code re-entering.
• Enter all four digits again;
54
PANDORA DXL 1090L SERVICE-SECURITY SYSTEM
simultaneously (on the remote control) and
VALET
button twice. The system will
LED
indicator will turn off.
VALET
button. Press the button a number of
LED
indicator flashes. The system will
P R O G R A M M I N G T H E S Y S T E M
• If you were able to correctly enter the «Service PIN-code» twice, the indicator
will produce the series of red and green flashes, new PIN-code will be recorded, the
system will return to programming mode. In case of the incorrect code input the
indicator will be lit red, the system will return to programming mode.
Level 3 – Recording the idle speed to the system memory
To timely turn off the starter during automatic or remote engine start via digital or
analog tachometer input and the correct operation of the «Smart Turbo Timer», it is
necessary to record the engine idle speed.
To record idle speed to the non-volatile system memory, enter the programming
VALET
menu. Press
button three times. Switch on the ignition and start the engine
after entering this level of programming (the engine should be warmed-up, idle
speed should match the stable idle speed of the warmed-up engine). The system will
confirm the presence of the idle speed status with green flashes of
Wait until the stable idle speed will be reached and save the changes.
Saving changes:
VALET
Press
button once to save idle speed. Successful recording of the idle speed
will be confirmed with the series of red and green flashes of
system will exit programming menu and reboot after saving the idle speed.
Level 4 – Resetting to factory settings.
The procedure recovers the factory settings of the system without deleting previously
registered devices (tags, mobile device, relays, etc.) that is stored in the non-volatile memory.
To reset the settings enter the programming mode and press
VALET
four times. Press and hold
button for more than 4 seconds until siren
sound, then release the button. The system will confirm the resetting to the factory
LED
settings with a long red flash of
indicator. After that the system will return to a
programming mode.
Level 5 – Recording Bluetooth engine compartment module
To record a Bluetooth engine compartment module, enter programming mode and press
VALET
LED
button 5 times. The
indicator will light green and the system will enter the
USER MANUAL
LED
indicator.
LED
indicator. The
VALET
button
55
Advertisement
Table of Contents
