Table of Contents
Advertisement
Pandora Light – is a car service-security system built for cars with on-board voltage of 12V. It
is a complex engineering solution, which includes unique and modern technological software and
hardware solutions.
When building the Pandora Light we were using the most up-to-date electronics from world's
best manufacturers. The device is built using high-precision mounting and control machinery, thus
we guarantee highest possible quality, reliability and stable technical characteristics for the whole
operation period.
Pandora Light has a cryptographically strong authorization code with unique dialog algorithm
and individual 128 bit encryption key on every device. We guarantee 100% protection form electronic
hacking for the whole operation period.
The system is built for your convenience: it's ergonomic, reliable, has the highest security and
service characteristics, 3 years unconditional warranty and free service and support on the territory
of Russian Federation and nearest states. We are happy to provide any support we can – feel free to
use our online support.
WARNING! It is strongly advised to have professional car mechanic installing the system.
Any car electronics installer should be able to install Pandora Light using installation
scheme in this manual and Alarm Studio software. Most features are highly dependent
on competent installation. Our systems are thoroughly tested for quality, so if a feature fails to
produce expected result, most likely the problem is in improper installation.
This device has limited external factors resistance. It should not be subjected to water beyond occasional splatter, or operated in
temperatures outside -40 to +80° C range. All system components must be installed only in a car interior.
Our web site: www.pandorainfo.com
Customer support: support@pandorainfo.com
Pandora would like to thank you for
choosing our service-security system
Product is in conformity with Electromagnetic Compatibility
Directive EMC 2004/108/EC and R&TTE Directive 1999/5/EC
Advertisement
Table of Contents
Related Manuals for Pandora Light
Summary of Contents for Pandora Light
- Page 1 Pandora would like to thank you for choosing our service-security system Pandora Light – is a car service-security system built for cars with on-board voltage of 12V. It is a complex engineering solution, which includes unique and modern technological software and hardware solutions.
-
Page 2: Table Of Contents
Remote and automatic engine start Program neutral procedure (reservation mode) Remote engine start Code immobilizer function (pin-to-drive) System settings menu Engine heater Time channels Check car status Event history Automatic engine start Wires description Wiring diagram and connectors pin-out Security-service system Pandora Light... - Page 3 Preparing to program the system using a computer Updating firmware Programming using the VALET button Additional information Siren sound and light signalization Meaning of the LED indicator signals Checking the number of recorded remote controls System modules layout Warranty obligations...
-
Page 4: System Features
• Built in temperature sensor, additional engine temperature sensor. • Sequential unlocking of the doors. • Arming when the engine is running. • Automatic arming. • Can be complemented with BM-103/105 single-wire digital block relay. • Software updates via built-in micro-USB socket. Security-service system Pandora Light... -
Page 5: Security Zones
Car security zones Pandora Light service-security system guards following independent zones with corresponding zone notifications on the remote and recording alarms into the event history: • doors • front hood • trunk • ignition • brake pedal • triggering of the shock sensor (warning level) •... -
Page 6: Remote Control
• Goes dark when there is no connection with the base unit. Red indicator: • Flashes frequently if there is any notification • Flashes occasionally when there is no connection ATTENTION! A remote control is a unified control device. Its functions depend on security system model. Security-service system Pandora Light... -
Page 7: Quick Access Functions Of The Remote Control
Quick access functions of the remote control System is disarmed System is armed (no alarm events) Ignition is switched on Ignition is switched off Search mode – flashes of turn Lock doors without Arming with sound signals with arming confrmation (short press) sound signals for 5 seconds Search mode –... - Page 8 Arming when the Arming in 30 seconds engine is running with With sound notification (short press) sound confirmation Arming when the Arming in 30 seconds engine is running with without sound (1 sec.) sound confirmation notifcation Security-service system Pandora Light...
-
Page 9: Icons Of The Remote Control
Icons of the remote control Flashing when command Tilt sensor sending Security zone Security mode status Motion sensor security zone Doors security zone Remote control battery level Front hood 12 48 Numeric indicator displays security zone current time Trunk Security zone 12.0V Battery voltage Ignition... -
Page 10: Arming Procedure
2 flashes of turn signals. The remote will play “DISARMING” ringtone and security mode status icon will change to: short 2 ashes doors unlocking press press and hold for 1 sec. system disarming 2 ashes For disarming without sound confirmation press button for more than 1 second. Security-service system Pandora Light... -
Page 11: Unlocking A Trunk
If there were new alarming events during the time system was armed, siren will sound 4 times and turn signals will flash 4 times, the remote control will sound “WARNING!” ringtone (after “DISARMING” ringtone) and will indicate zones triggered. All recent alarm events can be viewed in the event history. Unlocking a trunk To independently unlock the trunk, no matter if the system is armed or not, press button and hold... -
Page 12: Car Search Function
30 seconds, the siren will sound and turn signals will flash once, indicating that the mode is triggered. To activate this mode without sound confirmation, press and hold both buttons for 1 second until the sound and vibration signal. Security-service system Pandora Light... -
Page 13: Panic Mode
short press 1 ash 30 sec. press and Doors locking, hold for 1 sec. system arming 1 ash To cancel delayed arming when it is triggered, simply press button. Panic mode If your car or you are in danger and you want to draw attention to your car, you can use PANIC mode. In this mode the siren will sound and turn signals will flash repeatedly for 30 seconds. -
Page 14: Program Neutral Procedure (Reservation Mode)
5. The engine will be stopped. Now the system is ready to perform remote and automatic engine start. xate the car using a handbrake leave the car, close the doors in 3 sec., «engine stop» the engine will be stopped, ringtone the system is ready to perform remote start short press Security-service system Pandora Light... -
Page 15: Remote Engine Start
Remote engine start If the system is prepared for remote start, to execute it, press and hold button for 3 seconds. Sound signal will confirm the command, LCD will show flashing engine operation icon signifying preparation to the engine start. In a few seconds the engine will be started, the remote will play “ENGINE START”... -
Page 16: Code Immobilizer Function (Pin-To-Drive)
• Control over car status, view event history engine preheater: channel 1 2 3 enabled controls channel remote start 1 2 3 controls settings Engine preheater: disabled • Control over timer channels • Remote and automatic engine start adjusting system CHECK controls Security-service system Pandora Light... - Page 17 sounds будильник enabled выключен siren settings sensors Valet mode adjusting будильник будильник sounds включен sounds • Sensors adjusting • Maintenance mode of the car disabled valet mode disabled будильник 14 45 выключен siren sounds sounds enabled valet mode будильник • siren signals adjusting •...
-
Page 18: Engine Heater
Timer channels Time channels can be used to implement additional functions and to control external devices. Timer channels can be adjusted via the Pandora Alarm Studio. To enter “TIME CHANNELS MENU”, shortly press button. The following presses of button will cause switching between channels. - Page 19 channel 3 channel 3 disabled channel 3 disabled channel 3 disabled disabled channel 1 2 3 channel 4 channel controls 1 2 3 channel 4 channel disabled 1 2 3 controls channel 4 disabled channel controls 1 2 3 channel 4 disabled channel controls...
-
Page 20: Check Car Status
Navigate several last events using (forward) and (back) buttons. Events are displayed by showing time of the event and flashing corresponding trigger zone indicators. arming arming 12:43 12:43 System CHECK controls disarming disarming 12:44 12:44 arming 12:43 disarming Security-service system Pandora Light 12:44... -
Page 21: Automatic Engine Start
Automatic engine start The system allows setting up modes of automatic engine start and stop. Synchronized real-time clock on the remote and base unit and other autonomous system settings allow many engine start options without needing to have the remote in command radio range. Automatic start and engine work conditions programming is done using LCD remote. - Page 22 – 20° start start by temp by temp disabled start temp start temp disabled work work start temp – 20° – 20° duration duration – 20° start temp work start temp work Security-service system Pandora Light – 20° duration work...
- Page 23 start temp start temp daily start – 20° start temp daily start enabled – 20° daily start enabled – 20° daily start enabled enabled work work stop by temp duration work increase. decrease duration stop by temp enabled duration stop by temp enabled stop by temp enabled...
-
Page 24: Wires Description
• Wire 12 (Yellow-black) (CAN2-L/CH2) — Wire of digital bus CAN2-Low. It connects to an appropriate CAN2-Low wire of a car. This channel can be assigned as an output (CH2), it will not work as a digital bus in this case. Security-service system Pandora Light... - Page 25 • Wire 13 (Blue-black) (CH1) — Factory setting is ‘Beeper’ . A negative output of additional channel with maximum load current 200mA. This output is multipurpose, it can operate in accordance with selected logic. • Wire 14 (Yellow) (INP6) — Factory setting is ‘Ignition’ . This wire connects to ignition switch or to an appropriate wire where 12V voltage appears when ignition is enabled and doesn’t disappear until the moment ignition is disabled.
-
Page 26: Wiring Diagram And Connectors Pin-Out
For remote engine start Black IMMO-KEY2 OUT/INP7 8 16 White IMMO-KEY1 IN IMMO-KEY1 OUT/INP1 Green Trunk switch VALET button External VALET button LIN-OUT White LIN-IN Black WARNING! micro-USB Engine Do not shield built-in Engine preheater temperature antenna. control sensor Webasto Thermotop Evo, Eberspaecher Sockets... - Page 27 IN5 - «Brake pedal/ wires Blue/White Fuel level input» 200mA Green CH3 - «To turn indicators» Gray INP2 - «Doors switch» 150mA Yellow/White CAN1-H Orange/White CAN1-L (-) 200mA CH5 - «Open trunk» Red/Black 3..100V, min 8Hz) «Tachometer input » White Pandora Light...
- Page 28 Pandora Brown Yellow Relay module RMD-5M Orange Geen/Red Blue/Red + 12V «Ignition/Start- CH9 - Stop button»* Brown (–) CH10 - «Starter» Yellow (–) CH6 - « /Brake pedal»* Orange (–) 20A** 20A** 20A** CH8 - «Bypass» Green (–) CH7 - «Blocking NC»...
- Page 29 Х7 Socket (Multifunctional channels) Use this socket when implementing bypass of original immobilizer using IMMO-KEY1 and IMMO-KEY2 multifunctional channels. Deselect any logic of INP1 and INP7 inputs in settings. Make connections in accordance with installation scheme. The settings of the socket are available in Alarm Studio. Disconnect the system from power supply after changing the settings.
-
Page 30: Sensor Settings
To enter «Shock sensor warning/alarm level» submenu, shortly press button. Sensor sensitivity can be set with short presses of buttons. To save new settings of the sensor, press and hold button for 1 second. To exit menu, press and hold button for 1 second. Security-service system Pandora Light... - Page 31 disabled датчик удара предвар. уров. shock sensor shock sensor alarm level enabled disabled shock sensor shock sensor shortly press to save enabled датчик удара enabled тревож. уров. датчик удара включен shock sensor тревож. уров. warn level shock sensor shock sensor disabled warn level warn level...
-
Page 32: Motion Sensor Settings
To save new settings of the sensor, press and hold for 1 second. adjusting tilt sensor increase decrease level = press and hold for 1 sec. to save To exit menu, press and hold button for 1 second. Security-service system Pandora Light... -
Page 33: Siren Signal Settings
Siren signal settings To configure siren sounds, select «SIREN SETTINGS» menu. Select one of the siren sound options using button. To save new settings, shortly press button. siren all sound signals are enabled settings siren settings siren settings siren settings siren warning signals are disabled settings... -
Page 34: Radio Channel Control Settings
To exit menu, press and hold button for 1 second. Security-service system Pandora Light... -
Page 35: Service/Valet Mode
Service/Valet mode It is recommended to put system into service mode before handing it to the car service or valet Valet mode parking. When this mode is switched on, security system stops interfering with built-in electronics and disables all functions to ease maintenance or parking. Moreover, you will not have to leave the remote control or radio tag to the valet or the mechanic. -
Page 36: Alarm Clock Settings
• take the battery out and place a new one on its place; • the remote is ready for use (switch it on by pressing and holding button for 3 seconds) It is recommended to keep an extra AAA battery. Security-service system Pandora Light... -
Page 37: Control Over The System In Case Of Emergency
CONTROL OVER THE SYSTEM IN CASE OF EMERGENCY In case you cannot disarm the system using a phone or immobilizer tag, the ‘Secret PIN-code’ can be used. The ‘Secret PIN-code’ is written on the owner’s plastic card under protective layer. Erase the 2-2-2-2 protective layer and use the VALET button to input the PIN-code. - Page 38 - For emergency arming when the engine is stopped, press and hold VALET button for 3 seconds. The system will be armed in 30 seconds. The LED indicator is lighting red during the countdown Security-service system Pandora Light...
-
Page 39: Programming The System
(all changes will be saved) after exiting programming mode using the ignition. All ways to exit the programming menu are accompanied by sound signals of the siren/beeper and light signals of the LED indicator. Light signals indicate the number of recorded remote controls. User manual... -
Page 40: Preparing To Program The System Using A Computer
Windows XP/Vista/7/8/10 and the Pandora Alarm Studio application (you can download it from pandorainfo.com). It is required to create an account in the Alarm Studio to use the Pandora CLONE for the remote engine start (you can register without a connection to a system). The Pandora CLONE procedure requires an Internet connection. - Page 41 If the main LCD remote control is off, switch it on in accordance with its manual. Enter programming menu and then press the VALET button once. The LED indicator will light green and the system will enter the remote controls recording mode. Remote controls are recorded (paired) one by one, in any order and without time limit.
- Page 42 PIN-code; sublevel 11.3 – confirmation of the PIN-code input). The system will automatically enter the sublevel 11.1 (Selecting buttons) after entering the level 11. The system can determine buttons via analog “Code immobilizer” input or via digital protocol of a Security-service system Pandora Light...
- Page 43 To control fuel level, make connection and configure the settings: • Setting is performed via the Pandora Alarm Studio. The “Use INP to control fuel level” item should be enabled in the settings, the factory setting of this input (input settings) must be unselected.
- Page 44 To reset all calibration values, proceed to the sublevel 11 (do not switch on the ignition). Reset confirmation is performed by pressing the lock button , exit without confirmation and exit the menu are performed by pressing the VALET button. Sublevel Fuel level 12-0 12-1 12-2 12-3 12-4 12-5 12-6 12-7 12-8 Security-service system Pandora Light...
- Page 45 12-9 12-10 100% 12-11 Reset all calibration values 12-12 Exit the programming mode Level 17 – Programming bypass original immobilizer Bypass learning procedure is performed on this level. A detailed manual can be found in installation scheme for a car in the Alarm Studio. User manual...
-
Page 46: Additional Information
ADDITIONAL INFORMATION Siren sound and turn light signals Signal name Signal Description Alarm, PANIC mode Incessant sound and light signals for 30 sec. Arming 1 sound signal /1 light signal Disarming 2 sound signal / 2 light signals “Sensors were triggered” signal when... -
Page 47: Checking The Number Of Recorded Remote Controls
Checking the number of recorded remote controls The number of recorded remote controls can be checked by the number of orange flashes of the LED indicator. Number of registered remote controls device can be checked every time the ignition is switched on when the system is disarmed. -
Page 48: System Modules Layout
System modules layout Ask the installer to mark system’s modules on the picture provided. This information can be important for diagnostics in case system malfunctions. Base unit Valet button Blocking relay Relay module Security-service system Pandora Light... -
Page 49: Warranty Obligations
WARRANTY OBLIGATIONS Manufacturer guarantees correct operation of the service-security system if exploitation, installation, storage and transportation conditions described in this manual were met. The system should only be used according to installation scheme and user manuals. The system is meant to be installed by the professional car electronics installers. We recognize that outside Russia the system can be installed by amateurs –... -
Page 50: Installation Certificate
Type _______________________________________________________________________________ ID number (VIN) _____________________________________________________________________ Registration number __________________________________________________________________ Security system specifications: Model Pandora Light Serial number _______________________________________________________________________ Service center name, full address and installer’s stamp ______________________________________ ___________________________________________________________________________________ ___________________________________________________________________________________ Signature__________________________________/________________________________________/ Signator Work accepted______________________________/________________________________________/ Signator Date «____»___________________20___y. Security-service system Pandora Light... -
Page 51: Acceptance Certificate
Acceptance certificate Model Pandora Light is in conformity with Electromagnetic Compatibility Directive EMC 2004/108/ EC and R&TTE Directive 1999/5/EC Serial number _______________________________________________________________________ Date of production ___________________________________________________________________ Responsible person’s signature (stamp) Packager ___________________________________________________________________________ Signature (personal stamp) Warranty card Model Pandora Light Serial number _______________________________________________________________________ Date of purchase «____»... - Page 52 Security-service system Pandora Light...