Table of Contents
Advertisement
W I R I N G D E S C R I P T I O N • W I R I N G D I A G R A M
VALET»
in Programming mode using «
•
Wire «8» (Black) («Ground»)
— It should be connected to the car body in a
grounding spot. This wire should be connected FIRST during installation.
Wire «9» (Blue) (INP4)
•
— Factory setting is «Neutral/Handbrake». This wire
connects to appropriate neutral/handbrake wire of the car. This input is
multipurpose, it can operate in accordance with selected logic.
•
Wire «10» (Brown-white) (INP3)
— Factory setting is «Front hood trigger». This
wire connects to appropriate wire that becomes grounded when the front hood
opens. This input is multipurpose, it can operate in accordance with selected logic.
•
Wire «11» (Orange-black) («CAN-Low»)
wire of the car.
•
Wire «12» (Yellow-black) (СН2)
— Factory setting is «Close central lock». A
negative impulse of 0,8 seconds is formed on the wire to close central lock. A
negative output of additional channel with maximum load capacity 200mA. This
output is multipurpose, it can operate in accordance with selected logic. CH2
output stops to operate as an output when a car model supported CAN2-bus is
selected.
Wire «13» (Blue-black) (CH1)
•
— Factory setting is «Free output». A negative
output of additional channel with maximum load capacity 200mA. This output is
multipurpose, it can operate in accordance with selected logic.
•
Wire «14» (Yellow) (INP6)
— Factory setting is «Ignition». This wire connects to
ignition lock or to appropriate wire where 12V voltage appears when ignition is
enabled and doesn't disappear until the moment ignition is disabled. This input is
multipurpose, it can operate in accordance with selected logic.
Wire «15» (Purple) («Siren»)
•
— It connects to siren control wire (+) (maximum
load current is 2A). This output is multipurpose, it can operate in accordance with
selected logic.
•
Wire «16» (Red) («Power supply» +12V)
conductor with constant voltage of 12V.
38
PANDORA DXL 1090L SERVICE-SECURITY SYSTEM
button.
— It connects to appropriate CAN-Low
— It should be connected to reliable
W I R I N G D E S C R I P T I O N • W I R I N G D I A G R A M
Х5 socket (Relay module)
•
Wire «1» (Blue) (CH7)
— Factory setting is «Blocking N.O.» This output is used
to control blocking relay with a normally open logic (it becomes grounded
when switching on the ignition and security system is not armed). A negative
output of additional channel with maximum load current 200mA. This output is
multipurpose, it can operate in accordance with selected logic.
Wire «2» (Orange) (CH6)
•
— Factory setting is «ACC». The channel is used to
control accessories. If «Car with START/STOP button» setting is enabled, the channel
will control brake pedal during remote or automatic engine start. A negative
output of additional channel with maximum load current 200mA. This output is
multipurpose, it can operate in accordance with selected logic.
Wire «3» (Brown) (CH9)
•
— Factory setting is «Ignition». This output is used to
switch on ignition. It allows implementing automatic engine start, turbo timer,
ignition support. If «Car with START/STOP button» setting is enabled, the channel
will operate in impulse mode to control the button. A negative output of additional
channel with maximum load current 200mA. This output is multipurpose, it can
operate in accordance with selected logic.
•
Wire «4» (Green) (CH8)
— Factory setting is «Bypass». Output activates during
remote or automatic engine start. A negative output of additional channel with
maximum load current 200mA. This output is multipurpose, it can operate in
accordance with selected logic
•
Wire «5» (Yellow) (CH10)
— Factory setting is «Starter». This output is used to
switch on starter of the car. A negative output of additional channel with maximum
load capacity 200mA. This output is multipurpose, it can operate in accordance
with selected logic.
It is not recommended to assign «Starter» to any other channel.
•
Wire «6» (Red)
— relay module power supply 12V
USER MANUAL
39
Advertisement
Table of Contents
