EnGenius SP-935 User Manual page 35

Access to the telephone network shall occur only if the code transmitted by the
handset matches the code set in the base unit. Similarly, ringing of the handset shall
occur only if the code transmitted by the base unit matches the code set in the
handset. The security code required by this Section may also be employed to
perform other communications functions, such as providing telephone billing
information. This security code system is to operate in accordance with the
following provisions.
(1) There must be provision for at least 256 possible discrete digital codes. Factory-
set codes must be continuously varied over at least 256 possible codes as each
telephone is manufactured. The codes may be varied either randomly, sequentially,
or using another systematic procedure.
(2) Manufacturers must use one of the following approaches for facilitating
variation in the geographic distribution of individual security codes:
(i) Provide a means for the user to readily select from among at least 256 possible
discrete digital codes. The cordless telephone shall be either in a non-operable
mode after manufacture until the user selects a security code or the manufacturer
must continuously vary the initial security code as each telephone is produced.
(ii) Provide a fixed code that is continuously varied among at least 256 discrete
digital codes as each telephone is manufactured.
(iii) Provide a means for the cordless telephone to automatically select a different
code from among at least 256 possible discrete digital codes each time it is
activated.
(iv) It is permissible to provide combinations of fixed, automatic, and user-
selectable coding provided the above criteria are met.
(3) A statement of the means and procedures used to achieve the required
protection shall be provided in any application for equipment authorization of a
cordless telephone.
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired
operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux
appareils radio exempts de licence. Son fonctionnement est sujet aux deux
conditions suivantes: (1) le dispositif ne doit pas produire de brouillage
préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un
brouillage susceptible de provoquer un fonctionnement indésirable.
IMPORTANT NOTE:
~69~
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This device has been designed to operate with an antenna having a maximum gain
of 2dBi. Antenna having a higher gain is strictly prohibited per regulations of
Industry Canada. The required antenna impedance is 50 ohms.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies
pour un environnement non contrôlé. Cet équipement doit être installé et utilisé
avec un minimum de 20cm de distance entre la source de rayonnement et votre
corps.
Ce dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximal
de dB 2. Une antenne à gain plus élevé est strictement interdite par les règlements
d'Industrie Canada. L'impédance d'antenne requise est de 50 ohms.
Telecom
This equipment complies with Part 68 of the FCC rules and the requirements
adopted by the ACTA. On the EUT of this equipment is a label that contains, among
other information, a product identifier in the format US: SNIW401BSP935. If
requested, this number must be provided to the telephone company.
The REN is used to determine the number of devices that may be connected
to a telephone line. Excessive RENs on a telephone line may result in the devices
not ringing in response to an incoming call. In most but not all areas, the sum of
RENs should not exceed five (5.0). To be certain of the number of devices that may
be connected to a line, as determined by the total RENs, contact the local telephone
company. For products approved after July 23, 2001, the REN for this product is part
of the product identifier that has the format US: SNIW401BSP935. The digits
represented by 01 are the REN without a decimal point (e.g., 03 is a REN of 0.3). For
earlier products, the REN is separately shown on the label.
If your equipment causes harm to the telephone network, the telephone
company may discontinue your service temporarily. If possible, they will notify you
in advance. But if advance notice is not practical, you will be notified as soon as
possible. You will be informed of your right to file a complaint with the FCC. Your
telephone company may make changes in its facilities, equipment, operations or
procedures that could affect the proper functioning of your equipment. If they do,
you will be notified in advance to give you an opportunity to maintain
uninterrupted telephone service.
If you experience trouble with this telephone equipment, please contact the
following address and phone number for information on obtaining service or repairs.
~70~