Base Settings - EnGenius SP-935 User Manual

(2) Press SAVE left soft key to confirm selection.
Re: When Set "On", the handset match the caller ID with the phone book
entries; once matched, the LCD screen will display the name or
nickname instead of pure caller ID info (needs Call Waiting with Caller
ID service from local telephone company)
f. Press 6 to set Custom Name:
(1) Enter characters using the Character Table and method discussed in the
Phonebook section.
(2) Use
or to move the cursor backward or forward to insert
(to the left of the cursor) or delete (the character above the cursor, or
left of the cursor if cursor is on the right of the last character).
(3) Press SAVE (Left) soft key to confirm setting.
Re: Once entering the custom name, the greeting of LCD in standby mode
will be changed as the entering.
Default greeting is "SP-935".
g. Press 7 to Change Password:
(1) Enter original (4 digits) of handset then press
enter this menu.
(2) Enter new password (4 digits) then press
new password.
h. Press 8 to set Headset Ring: See Headset Ring operation on Page 52.
7. Press 6 to set Base Settings:
When enter this menu, you must enter Base PIN code first (4 digits).
Re: The PIN code is for Base Settings. Default is "0000".
a. Press 1 to set DTMF Duration.
Enter the DTMF duration (90~200ms), press
(1)
the setting. Default is 100ms.
Re: Please check with your dealer before you change it. If the duration not
matches with PSTN or PBX setting, it may operate faultily.
b. Press 2 select flash key timing. Default is 600ms.
OK left soft key when
SAVE left soft key to confirm
OK left soft key to confirm
~63~
(1)
Use or to scroll through option 1~9 (100~900ms). Or press
digit key (1~9) directly.
Press SELECT left soft key to confirm selection.
(2)
Re: The default value (600 ms) works in most areas. Changing this setting
may cause Flash key not working. Change only when you are certain of
the new value would work.
c. Press 3 to set Assign Next HS
Enter 2-digit handset ID followed by pressing
(1)
When register a new handset, the base will assign the specific handset
(2)
ID which assigned in advance to the new handset.
d. Press 4 to set Clear HS
Enter 2-digit handset ID followed by pressing
(1)
The base will erase the handset ID from system.
(2)
e. Press 5 to Change PIN:
Enter the new Base PIN followed by
(1)
Re: Default Base PIN is "0000".
f. Press 6 to set Auto Hang Up:
Use CHANGE left soft key to select and confirm on or off.
(1)
Re: When setting "on", the SP-935 will automatically hang up if the far end
caller hung up already. However, this function depends on if there is
"dial tone or busy tone" signal sent out by PBX or PSTN, after the call
hung up.
g. Press 7 to Set Time to support DTMF Caller ID:
Use SAVE left soft key to select and confirm the Date and Time you
(1)
have set (see Set Time operation on page 20).
f. Press 8 to set Line Detection:
Use CHANGE left soft key to select and confirm on or off.
(1)
Re: When setting "on", the SP-935 will automatically see if the telephone
line is plugged in or not. Once the telephone line is not available, user
can't select the line to make an outgoing call manually.
8. Press 7 to register, de-register handset : see Handset Registration operation on
Page 36,
9. Press 8 to set Menu Display:
To avoid mis-setup of Call Settings (MENU-4), Phone Settings (MENU-5) and Base
Settings (MENU-6), you can hide these menus, so that other handset users won't
have chance to mis-settup these settings.
Re: When entering the Menu Display, you have to enter password first.
OK left soft key.
OK left soft key.
OK left soft key.
~64~